- 您現在的位置：買賣IC網 > PDF目錄378545 > DF1704E Stereo, 24-Bit, 96kHz 8X Oversampling Digital Interpolation Filter DIGITAL-TO-ANALOG CONVERTER PDF資料下載
參數資料
| 型號： | DF1704E |
| 英文描述： | Stereo, 24-Bit, 96kHz 8X Oversampling Digital Interpolation Filter DIGITAL-TO-ANALOG CONVERTER |
| 中文描述： | 立體聲，24位，96kHz的8倍過采樣數字插值濾波器的數字模擬轉換器 |
| 文件頁數： | 6/16頁 |
| 文件大小： | 222K |
| 代理商： | DF1704E |
6
DF1704
RESET
The DF1704 has both an internal power-on reset circuit and
a reset pin, RST (pin 14), for providing an external reset
signal. The internal power-on reset is performed automati-
cally when power is applied to the DF1704, as shown in
Figure 2. The RST pin can be used to synchronize the
DF1704 with a system reset signal, as shown in Figure 3.
SYSTEM CLOCK REQUIREMENTS
The system clock of the DF1704 can be supplied by either
an external clock signal at XTI (pin 6), or by the on-chip
crystal oscillator. The system clock rate must run at 256f
S
,
384f
S
, 512f
S
, or 768f
S
, where f
S
is the audio sampling rate.
It should be noted that a 768f
S
system clock cannot be used
when f
S
= 96kHz. In addition, the on-chip crystal oscillator
is limited to a maximum frequency of 24.576MHz. Table I
shows the typical system clock frequencies for selected
sample rates.
The DF1704 includes a system clock detection circuit that
determines the system clock rate in use. The circuit com-
pares the system clock input (XTI) frequency with the
LRCIN input rate to determine the system clock multiplier.
Ideally, LRCIN and BCKIN should be derived from the
system clock to ensure proper synchronization. If the phase
difference between the system clock and LRCIN is larger
than
±
6 bit clock (BCKIN) periods, the synchronization of
the system and LRCIN clocks will be performed automati-
cally by the DF1704.
Timing requirements for the system clock input are shown in
Figure 1.
AUDIO INPUT INTERFACE
The audio input interface is comprised of BCKIN (pin 2),
LRCIN (pin 28), and DIN (pin 1).
BCKIN is the input bit clock, which is used to clock data
applied at DIN into the DF1704’s input serial interface.
Input data at DIN is clocked into the DF1704 on the rising
edge of BCKIN. The left/right clock, LRCIN, is used as a
word latch for the audio input data.
BCKIN can run at 32f
S
, 48f
S
, or 64f
S
, where f
S
is the audio
sample frequency. LRCIN is run at the f
S
rate. Figures 4 (a)
through 4 (c) show the input data formats, which are sel-
ected by hardware or software controls. Figure 5 shows the
audio input interface timing requirements.
SYSTEM CLOCK FREQUENCY (MHz)
SAMPLING RATE FREQUENCY (f
S
)
256f
S
384f
S
512f
S
768f
S
32kHz
8.1920
12.2880
16.3840
24.5760
44.1kHz
11.2896
16.9340
22.5792
33.8688
(1)
48kHz
12.2880
18.4320
24.5760
36.8640
(1)
96kHz
24.5760
(3)
36.8640
(1)
49.1520
(1)
See Notes 1, 2
NOTES: (1) Maximum crystal oscillator frequency is 24.576MHz and cannot be used for these combinations. (2) 768f
S
system clock cannot be used with 96kHz
sampling rate. (3) Use external system clock applied at XTI.
TABLE I. Typical System Clock Frequencies.
FIGURE 1. System Clock Timing.
1024 system clocks
Reset
Reset Removal
V
DD
2.2V
2.6V
1.8V
Internal Reset
System Clock
FIGURE 2. Internal Power-On Reset Timing.
FIGURE 3. External Forces Reset Timing.
t
SCKH
System Clock Pulse Width HIGH
System Clock Pulse Width LOW
:t
SCKIH
:t
SCKIL
:7ns min
(1)
:7ns min
(1)
t
SCKL
2.0V
0.8V
“H”
“L”
XTI
NOTE: (1) For f
S
= 96kHz and SCK = 256f
S
, t
SCKIH
= 14ns (min)
t
SCKIL
= 14ns (min)
For f
S
≠
96kHz and SCK = 256f
S
, t
SCKIH
= 20ns (min)
t
SCKIL
= 20ns (min)
1024 system (XTI) clocks
Reset
Reset Removal
System Clock
Internal Reset
RST
t
RST
t
RST
≥
20ns
During the power-on reset period (1024 system clocks), the
DF1704 outputs are forced LOW. For an external forced
reset, the outputs are forced LOW during the initialization
period (1024 system clocks), which occurs after the LOW-
to-HIGH transition of the RST pin as shown in Figure 3.
相關PDF資料 |
PDF描述 |
|---|---|
| DF1760 | Multi-Bit Enhanced Noise Shaping 20-Bit ANALOG-TO-DIGITAL CONVERSION SYSTEM |
| DF1B-R28A | MOSFET N-CH 500V 64A SOT-227 |
| DF1B-28PRB | 2.5mm Pitch Connector for Discrete Wire Connection (Product Compliant with UL/CSA Standard) |
| DF1B-28PRF | 2.5mm Pitch Connector for Discrete Wire Connection (Product Compliant with UL/CSA Standard) |
| DF1B-28PRFB | 2.5mm Pitch Connector for Discrete Wire Connection (Product Compliant with UL/CSA Standard) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DF1704E/2K | 功能描述:音頻數/模轉換器 IC 8X Oversampling Filter RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel |
| DF1704E/2KG4 | 功能描述:音頻數/模轉換器 IC 8X Oversampling Filter RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel |
| DF1704EG4 | 功能描述:音頻數/模轉換器 IC 8X Oversampling Filter RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel |
| DF1706 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Stereo, 24-Bit, 192kHz 8x Oversampling Digital Interpolation Filter |
| DF1706E | 功能描述:有源濾波器 8X Oversampling Digi Interpolation Filter RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。