- 您現在的位置：買賣IC網 > PDF目錄376588 > DCP010505BP-U Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS PDF資料下載
參數資料
| 型號： | DCP010505BP-U |
| 英文描述： | Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS |
| 中文描述： | 微型1W隔離未穩(wěn)壓DC / DC轉換器 |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 453K |
| 代理商： | DCP010505BP-U |
DCP01B SERIES
SBVS012B
DECEMBER 2000
REVISED OCTOBER 2004
www.ti.com
13
DUAL OUTPUT VOLTAGE DCP AND DCVs
The voltage output for the dual DCPs is half wave rectified;
therefore, the discharge time is 1.25
μ
s. Repeating the
above calculations using the 100% load resistance of 25
(0.2A per output), the results are shown below:
τ
= 25
μ
s
T
DIS
= 1.25
μ
s.
V
DIS
= 244mV
V
ESR
= 20mV
Ripple Voltage = 266mV
This time, it is the capacitor discharging that is contributing
to the largest component of ripple. Changing the output
filter to 10
μ
F, and repeating the calculations:
Ripple Voltage = 45mV.
This value is composed of almost equal components.
The above calculations are given only as a guide.
Capacitor parameters usually have large tolerances and
can be susceptible to environmental conditions.
PCB LAYOUT
Figure 5 and Figure 6 illustrate a printed circuit board
(PCB) layout for the two conventional (DCP01/02,
DCV01), and two SO-28 surface-mount packages
(DCP02U). Figure 7 shows the schematic.
Input power and ground planes have been used, providing
a low-impedance path for the input power. For the output,
the common or 0V has been connected via a ground plane,
while the connections for the positive and negative voltage
outputs are conducted via wide traces in order to minimize
losses.
The location of the decoupling capacitors in close
proximity to their respective pins ensures low losses due
to the effects of stray inductance; thus, improving the ripple
performance. This is of particular importance to the input
decoupling capacitor as this supplies the transient current
associated with the fast switching waveforms of the power
drive circuits.
The Sync pin, when not being used, is best left as a floating
pad. A ground ring or annulus connected around the pin
will prevent noise being conducted onto the pin. If the Sync
pin is being connected to one or more Sync pins, then the
linking trace should be narrow and must be kept short in
length. In addition, no other trace should be in close
proximity to this trace because that will increase the stray
capacitance on this pin, and that will effect the
performance of the oscillator.
Ripple and Noise
Careful consideration should be given to the layout of the
PCB, in order that the best results can be obtained.
The DCP01B is a switching power supply and as such can
place high peak current demands on the input supply. In
order to avoid the supply falling momentarily during the
fast switching pulses, ground and power planes should be
used to connect the power to the input of DCP01B. If this
is not possible, then the supplies must be connected in a
star formation with the traces made as wide as possible.
If the SYNC
IN
pin is being used, then the trace connection
between device SYNC
IN
pins should be short to avoid
stray capacitance. If the SYNC
IN
pin is not being used, it
is advisable to place a guard ring (connected to input
ground) around this pin to avoid any noise pick up.
The output should be taken from the device using ground
and power planes; this ensures minimum losses.
A good quality low-ESR ceramic capacitor placed as close
as practical across the input will reduce reflected ripple
and ensure a smooth startup.
A good quality low-ESR capacitor (ceramic preferred)
placed as close as practical across the rectifier output
terminal and output ground gives the best ripple and noise
performance. See SBVA012 for more information on noise
rejection.
THERMAL MANAGEMENT
Due to the high power density of this device, it is advisable
to provide ground planes on the input and output.
相關PDF資料 |
PDF描述 |
|---|---|
| DCP010505DB | Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS |
| DCP010505DBP | Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS |
| DCP010505DBP-U | Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS |
| DCP010505DP | Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS |
| DCP011512 | Miniature, 1W Isolated UNREGULATED DC/DC CONVERTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DCP010505BP-U | 制造商:Texas Instruments 功能描述:IC's |
| DCP010505BP-U | 制造商:Texas Instruments 功能描述:IC DC/DC CONVERTER 1W 5V/5V 10505 |
| DCP010505BP-U/700 | 功能描述:DC/DC轉換器 Mini 1W Iso Unreg DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| DCP010505BP-U/7E4 | 功能描述:DC/DC轉換器 Mini 1W Iso Unreg DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| DCP010505BP-UE4 | 功能描述:DC/DC轉換器 Mini 1W Iso Unreg DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發(fā)布緊急采購，3分鐘左右您將得到回復。