- 您現在的位置：買賣IC網 > PDF目錄295418 > DB0805A1900AWTR (AVX CORP) DIR-COUPLER 3DB 1850-1950MHZ THIN-FILM SMD-0805 LGA-SN90/PB10 T&R PDF資料下載
參數資料
| 型號： | DB0805A1900AWTR |
| 廠商： | AVX CORP |
| 元件分類： | 耦合器 |
| 英文描述： | DIR-COUPLER 3DB 1850-1950MHZ THIN-FILM SMD-0805 LGA-SN90/PB10 T&R |
| 中文描述： | 1850 MHz - 1950 MHz RF/MICROWAVE 90 DEGREE HYBRID COUPLER, 0.3 dB INSERTION LOSS-MAX |
| 封裝： | MINIATURE PACKAGE-4 |
| 文件頁數： | 5/13頁 |
| 文件大小： | 313K |
| 代理商： | DB0805A1900AWTR |
76
3
Thin-Film Directional Couplers
DB0805 3dB 90° Test Jigs
GENERAL DESCRIPTION
These jigs are designed for testing the DB0805 3dB 90°
Couplers using a Vector Network Analyzer.
They consist of a dielectric substrate, having 50
Ω microstrips
as conducting lines and a bottom ground plane located at a
distance of 0.254mm from the microstrips.
The substrate used is Neltec’s NH9338ST0254C1BC.
The connectors are SMA type (female), ‘Johnson Components
Inc.’ Product P/N: 142-0701-841.
Both a measurement jig and a calibration jig are provided.
The calibration jig is designed for a full 2-port calibration, and
consists of an open line, short line and through line. LOAD
calibration can be done by a 50
Ω SMA termination.
When measuring a component, it can be either soldered or
pressed using a non-metallic stick until all four ports touch
the appropriate pads. Set the VNA to the relevant frequency
band. Connect the VNA using a 10dB attenuator on the jig
terminal connected to port 2. Follow the VNA’s instruction
manual and use the calibration jig to perform a full 2-port
calibration in the required bandwidths.
Place the coupler on the measurement jig as follows:
Input (Coupler)
Connector 1 (Jig)
Output 1 (Coupler)
Connector 3 (Jig)
50
Ω (Coupler)
Connector 2 (Jig)
Output 2 (Coupler)
Connector 4 (Jig)
To measure R. Loss and I. Loss 1 connect:
Connector 1 (Jig)
Port 1 (VNA) Connector 3 (Jig) Port 2 (VNA)
Connector 2 (Jig)
50Ω
Connector 4 (Jig)
50Ω
To measure R. Loss and I. Loss 2 connect:
Connector 1 (Jig)
Port 1 (VNA) Connector 3 (Jig) 50Ω
Connector 2 (Jig)
50Ω
Connector 4 (Jig)
Port 2 (VNA)
To measure Isolation connect:
Connector 1 (Jig)
50Ω
Connector 3 (Jig)
Port 1 (VNA)
Connector 2 (Jig)
50Ω
Connector 4 (Jig)
Port 2 (VNA)
MEASUREMENT PROCEDURE
Measurement Jig
Connector 1
Connector 2
Connector 4
Connector 3
Calibration Jig
Short Line
to GND
Load &
Through
Load &
Through
Connector
Johnson
P/N 142-0701-841
Open
Line
相關PDF資料 |
PDF描述 |
|---|---|
| DB2805S/F | 1-OUTPUT 20 W DC-DC REG PWR SUPPLY MODULE |
| DB5W5PA4F | 5 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| DBC-30-X-1-1-FC-2-X | FIBER OPTIC SPLITTER/COUPLER, 1X2PORT, 70/30, PANEL MOUNT, FC/SPC CONNECTOR |
| DBC-30-13/15-2-2-ST/UPC-9L-1 | FIBER OPTIC SPLITTER/COUPLER, 1270-1350nm, 2X2PORT, 70/30, PANEL MOUNT, ST/UPC CONNECTOR |
| DBC-30-13/15-2-2-ST-9L-1 | FIBER OPTIC SPLITTER/COUPLER, 1270-1350nm, 2X2PORT, 70/30, PANEL MOUNT, ST/SPC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DB0805A1920AWTR | 功能描述:信號調節 Directional Coupler 1920 MHz +/- 50 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| DB0805A1920AWTR\500 | 功能描述:信號調節 Directional Coupler 1920 MHz +/- 50 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| DB0805A1950ASTR | 功能描述:信號調節 Directional Coupler 1950 MHz +/- 50 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| DB0805A1950ASTR\\500 | 制造商:AVX Corporation 功能描述:AVX DESIGN WIN PART LOAD - Tape and Reel |
| DB0805A1950ASTR\500 | 功能描述:信號調節 Directional Coupler 1950 MHz +/- 50 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。