- 您現在的位置：買賣IC網 > PDF目錄8957 > DAC8531IDRBT (Texas Instruments)IC DAC 16BIT RRO LP 8-SON PDF資料下載
參數資料
| 型號： | DAC8531IDRBT |
| 廠商： | Texas Instruments |
| 文件頁數： | 6/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT RRO LP 8-SON |
| 產品培訓模塊： | Data Converter Basics |
| 標準包裝： | 1 |
| 設置時間： | 8µs |
| 位數： | 16 |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 720µW |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VDFN 裸露焊盤 |
| 供應商設備封裝： | 8-SON 裸露焊盤（3x3） |
| 包裝： | 標準包裝 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | 93k |
| 配用： | 296-13548-ND - EVAL MOD FOR DAC8531 |
| 其它名稱： | 296-15727-6 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DAC8531
14
SBAS192B
www.ti.com
power supply is quite noisy or if the system supply voltages
are at some value other than 5V. The REF02 will output a
steady supply voltage for the DAC8531. If the REF02 is
used, the typical current it needs to supply to the DAC8531
is 250
A. This is with no load on the output of the DAC.
When the DAC output is loaded, the REF02 also needs to
supply the current to the load. The total current required (with
a 5k
load on the DAC output) is:
250
A + (5V/5k) = 1.29mA
The load regulation of the REF02 is typically 0.005%/mA,
which results in an error of 322
V for the 1.29mA current
drawn from it. This corresponds to a 4.2LSB error.
BIPOLAR OPERATION USING THE DAC8531
The DAC8531 has been designed for single-supply operation
but a bipolar output range is also possible using the circuit in
Figure 10. The circuit shown will give an output voltage range
of
±V
REF. Rail-to-rail operation at the amplifier output is achiev-
able using an OPA703 as the output amplifier.
The output voltage for any input code can be calculated as
follows:
VV
D
RR
R
V
R
O
REF
=
+
65536
12
1
2
1
–
where D represents the input code in decimal (0–65535).
With VREF = 5V, R1 = R2 = 10k:
V
D
V
O =
10
65536
5
–
This is an output voltage range of
±5V with 0000
H corre-
sponding to a –5V output and FFFFH corresponding to a +5V
output. Similarly, using VREF = 2.5V, ±2.5V output voltage
raw can be achieved.
LAYOUT
A precision analog component requires careful layout, ad-
equate bypassing, and clean, well-regulated power supplies.
As the DAC8531 offers single-supply operation, it will often
be used in close proximity with digital logic, microcontrollers,
microprocessors, and digital signal processors. The more
digital logic present in the design and the higher the switch-
ing speed, the more difficult it will be to keep digital noise
from appearing at the output.
Due to the single ground pin of the DAC8531, all return
currents, including digital and analog return currents, must
flow through the GND pin. Ideally, GND would be connected
directly to an analog ground plane. This plane would be
separate from the ground connection for the digital compo-
nents until they were connected at the power-entry point of
the system.
The 68HC11 should be configured so that its CPOL bit is a
0 and its CPHA bit is a 1. This configuration causes data
appearing on the MOSI output to be valid on the falling edge
of SCK. When data is being transmitted to the DAC, the
SYNC line is taken LOW (PC7). Serial data from the 68HC11
is transmitted in 8-bit bytes with only eight falling clock edges
occurring in the transmit cycle. Data is transmitted MSB first.
In order to load data to the DAC8531, PC7 is left LOW after
the first eight bits are transferred, then a second and third
serial write operation is performed to the DAC and PC7 is
taken HIGH at the end of this procedure.
APPLICATIONS
USING REF02 AS A POWER SUPPLY FOR
THE DAC8531
Due to the extremely low supply current required by the
DAC8531, an alternative option is to use a REF02 +5V
precision voltage reference to supply the required voltage to
the part, as shown in Figure 9. This is especially useful if the
FIGURE 8. DAC8531 to 68HC11 Interface.
FIGURE 9. REF02 as a Power Supply to the DAC8531.
DAC8531 TO 68HC11 INTERFACE
Figure 8 shows a serial interface between the DAC8531 and
the 68HC11 microcontroller. SCK of the 68HC11 drives the
SCLK of the DAC8531, while the MOSI output drives the
serial data line of the DAC. The SYNC signal is derived from
a port line (PC7), similar to what was done for the 8051.
68HC11(1)
PC7
SCK
MOSI
SYNC
SCLK
D
IN
DAC8531(1)
NOTE: (1) Additional pins omitted for clarity.
REF02
DAC8531
Three-Wire
Serial
Interface
+5V
285
A
V
OUT = 0V to 5V
SYNC
SCLK
D
IN
+15
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B0Y-MX-F1 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VE-B0W-MY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| VE-B0V-MY-F1 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-B0T-MY-F1 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-B0R-MY-F1 | CONVERTER MOD DC/DC 7.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC8531IDRBTG4 | 功能描述:數模轉換器- DAC Lo-Pwr R-to-R Out 16-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8532 | 制造商:BB 制造商全稱:BB 功能描述:Dual Channel, Low Power, 16-Bit, Serial Input DIGITAL-TO-ANALOG CONVERTER |
| DAC8532IDGK | 功能描述:數模轉換器- DAC 16-Bit Dual Ch Low Power DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8532IDGK | 制造商:Texas Instruments 功能描述:16BIT DUAL DAC SMD 8532 MSOP8 |
| DAC8532IDGKG4 | 功能描述:數模轉換器- DAC 16-Bit Dual Ch Low Power DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。