- 您現在的位置：買賣IC網 > PDF目錄376564 > DAC8531EVM (Texas Instruments, Inc.) DAC8531 Evaluation Module(DAC8531評估板) PDF資料下載
參數資料
| 型號： | DAC8531EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DAC8531 Evaluation Module(DAC8531評估板) |
| 中文描述： | DAC8531評估模塊（DAC8531評估板） |
| 文件頁數： | 24/42頁 |
| 文件大?。?/td> | 788K |
| 代理商： | DAC8531EVM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Stand-Alone DC Mode Test
3-2
3.1
Stand-Alone DC Mode Test
The stand-alone mode (SAM) test is performed only in dc mode to quickly
verify the EVM board for proper functionality. Apply a dc power source of 3.3 V
to 5 V with the +supply connecting to J2
–
2 and referenced to J2
–
1. The power
indicator light, D3, should illuminate (green) once the power is applied.
To put the EVM board into stand-alone (or self-test) mode, the SW1B and
SW1A switches must be on. The self-test indicator light, D1, should also
illuminate to indicate that the EVM board is now in self-test mode.
3.1.1
Factory Default
The EVM board is set from the factory to the configuration listed in the table
below to operate with a single supply and unity gain buffer output through U12.
Table 3
–
1.Factory Default Jumper Setting
Reference
Jumper
Position
Function
W2
1
–
2
Serial data input from SAM circuit to the DAC data input pin, DIN
W3
1
–
2
Serial clock from SAM circuit to the DAC serial clock input pin, SCLK
W4
1
–
2
Frame sync signal from SAM circuit to the DAC sync input pin, SYNC
W5
1
–
2
SAM frame sync (FS) enabled for 24 SCLK cycles
W6
1
–
2
SAM data enabled for 24-bit serial data stream
W7
1
–
2
+Supply rail for U12 (signal conditioning circuit)
W8
1
–
2
GND for U12
W9
OPEN
EVM power supply is not provided by the DSP starter kit (see Note).
W10
OPEN
U12 is configured for unity gain.
W11
OPEN
U12 is configured for unity gain.
W12
OPEN
Bipolar supply is not selected.
W13
3
–
4
DAC output signal is conditioned and directed to J11, J3
–
1, and TP1 output terminals.
W14
1
–
2
Adjustable onboard reference voltage is selected.
J4
OPEN
Enable parallel load of data inputs for U5, U6, and U7
Note:
Jumper must be removed if external power is applied to avoid damaging the DSP Starter Kit.
3.1.2
Test Mode Operation
Briefly mentioned earlier, the switch bank SW1 provides control for the
stand-alone mode of operation. Switch SW1B controls the start and stop of the
SAM serial clock and SW1A controls the go signal for the SAM circuitry. When
both switches are on, the self-test indicator light (yellow) turns on.
Switch banks SW2 and SW3 provides the two control bits and the six MSB data
bits for the 16-bit DAC. SW2A and SW2B is the control bit generator, which
allows the DAC to be programmed into four separate modes of operation, see
Table 3
–
2. SW2A and SW2B maps out to PD1 (DB17) and PD0 (DB16)
respectively of the DAC data input register (16-bit version). Figure 3
–
1 shows
相關PDF資料 |
PDF描述 |
|---|---|
| DAC8532 | Dual Channel, Low Power, 16-Bit, Serial Input DIGITAL-TO-ANALOG CONVERTER |
| DAC8532IDGKR | BASE, BLACK; |
| DAC8532IDGK | Dual Channel, Low Power, 16-Bit, Serial Input DIGITAL-TO-ANALOG CONVERTER |
| DAC8541EVM | DAC8541EVM(DAC8541評估板) |
| DAC8544I | QUAD, 16-BIT, RAIL-TO-RAIL VOLTAGE OUTPUT, PARALLEL INTERFACE, DIGITAL-TO-ANALOG CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC8531IDRB | 制造商:Texas Instruments 功能描述: |
| DAC8531IDRBR | 功能描述:數模轉換器- DAC Lo-Pwr R-to-R Out 16-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8531IDRBRG4 | 功能描述:數模轉換器- DAC Lo-Pwr R-to-R Out 16-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8531IDRBT | 功能描述:數模轉換器- DAC Lo-Pwr R-to-R Out 16-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8531IDRBTG4 | 功能描述:數模轉換器- DAC Lo-Pwr R-to-R Out 16-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。