- 您現在的位置：買賣IC網 > PDF目錄376560 > DAC7615U Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) PDF資料下載
參數資料
| 型號： | DAC7615U |
| 元件分類： | 外設及接口 |
| 英文描述： | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| 中文描述： | 單電源RS232C接口線路驅動器/接收器（單電源RS232C接口線收發器（2發2收）） |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 485K |
| 代理商： | DAC7615U |
11
DAC7615
STATE OF
SELECTED
INPUT
REGISTER
SELECTED
INPUT
REGISTER
STATE OF
ALL DAC
REGISTERS
A1
A0
LOADREG
LOADDACS
RESET
L
(1)
L
L
H
(2)
H
A
Transparent
Latched
L
H
L
H
H
B
Transparent
Latched
H
L
L
H
H
C
Transparent
Latched
H
H
L
H
H
D
Transparent
Latched
X
(3)
X
H
L
H
NONE
(All Latched)
Transparent
X
X
H
H
H
NONE
(All Latched)
Latched
X
X
X
X
L
ALL
Reset
(4)
Reset
(4)
NOTES: (1) L = Logic LOW. (2) H = Logic HIGH. (3) X = Don’t Care. (4) Resets to either 000H or 800
H
, per the RESETSEL state (LOW = 000
H
, HIGH = 800
H
).
When RESET rises, all registers that are in their latched state retain the reset value.
TABLE II. Control Logic Truth Table.
CS
(1)
CLK
(1)
LOADREG
RESET
SERIAL SHIFT REGISTER
H
(2)
X
(3)
H
H
No Change
L
(4)
L
H
H
No Change
L
↑
↑
(5)
L
H
H
Advanced One Bit
H
H
Advanced One Bit
H
(6)
X
L
(7)
H
No Change
H
(6)
X
H
L
(8)
No Change
NOTES: (1) CS and CLK are interchangeable. (2) H = Logic HIGH. (3) X =
Don’t Care. (4) L = Logic LOW (5) = Positive Logic Transition. (6) A HIGH
value is suggested in order to avoid a “false clock” from advancing the shift
register and changing the shift register. (7) If data is clocked into the serial
register while LOADREG is LOW, the selected input register will change as the
shift register bits “flow” through A1 and A0. This will corrupt the data in each
input register that has been erroneously selected. (8) RESET LOW causes no
change in the contents of the serial shift register.
TABLE III. Serial Shift Register Truth Table.
If both CS and CLK are used, then CS should rise only when
CLK is HIGH. If not, then either CS or CLK can be used to
operate the shift register. See Table III for more information.
The digital data into the DAC7615 is double-buffered. This
allows new data to be entered for each DAC without disturb-
ing the analog outputs. When the new settings have been
entered into the device, all of the DAC outputs can be
updated simultaneously. The transfer from the input regis-
ters to the DAC registers is accomplished with a HIGH to
LOW transition on the LOADDACS input.
Because the DAC registers become transparent when
LOADDACS is LOW, it is possible to keep this pin LOW
and update each DAC via LOADREG. However, as each
new data word is entered into the device, the corresponding
output will update immediately when LOADREG is taken
LOW.
Digital Input Coding
The DAC7615 input data is in Straight Binary format. The
output voltage is given by the following equation:
Note that CS and CLK are combined with an OR gate and
the output controls the serial-to-parallel shift register inter-
nal to the DAC7615 (see the block diagram on the front of
this data sheet). These two inputs are completely inter-
changeable. In addition, care must be taken with the state of
CLK when CS rises at the end of a serial transfer. If CLK is
LOW when CS rises, the OR gate will provide a rising edge
to the shift register, shifting the internal data one additional
bit. The result will be incorrect data and possible selection of
the wrong input register.
where N is the digital input code (in decimal). This equation
does not include the effects of offset (zero-scale) or gain
(full-scale) errors.
(V
REFH
– V
REFL
) N
4096
V
OUT
= V
REFL
+
相關PDF資料 |
PDF描述 |
|---|---|
| DAC7615UB | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7616 | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7616U | Quad, Serial Input, 12-Bit, Voltage Output DIGITAL-TO-ANALOG CONVERTER |
| DAC7616UB | Quad, Serial Input, 12-Bit, Voltage Output DIGITAL-TO-ANALOG CONVERTER |
| DAC7616E | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC7615U/1K | 功能描述:數模轉換器- DAC Quad Ser In 12-Bit Voltage Output RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7615U/1KG4 | 功能描述:數模轉換器- DAC Quad Ser In 12-Bit Voltage Output RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7615UB | 功能描述:數模轉換器- DAC Quad Ser In 12-Bit Voltage Output RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7615UB/1K | 功能描述:數模轉換器- DAC Quad Ser In 12-Bit Voltage Output RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7615UB/1KG4 | 功能描述:數模轉換器- DAC Quad Ser In 12-Bit Voltage Output RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。