- 您現在的位置：買賣IC網 > PDF目錄376560 > DAC7611U Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) PDF資料下載
參數資料
| 型號： | DAC7611U |
| 元件分類： | 外設及接口 |
| 英文描述： | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| 中文描述： | 單電源RS232C接口線路驅動器/接收器（單電源RS232C接口線收發器（2發2收）） |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 182K |
| 代理商： | DAC7611U |
12
DAC7611
As with the GND connection, V
DD
should be connected to
a +5V power supply plane or trace that is separate from the
connection for digital logic until they are connected at the
power entry point. In addition, the 10
μ
F and 0.1
μ
F capaci-
tors shown in Figure 4 are strongly recommended and
should be installed as close to V
DD
and ground as possible.
In some situations, additional bypassing may be required
such as a 100
μ
F electrolytic capacitor or even a “Pi” filter
made up of inductors and capacitors—all designed to essen-
tially lowpass filter the +5V supply, removing the high
frequency noise (see Figure 4).
OFFSET ERROR MEASUREMENT
As with most DACs, the DAC7611 can have an offset error
(or zero scale error) which is either negative or positive. If
the error is positive, the output voltage for an input code of
000
H
will be greater than 0V. If the error is negative, the
output voltage is below 0V. However, since the DAC7611 is
a single-supply device and cannot swing below ground, the
output voltage will be 0V, giving the impression that the
offset error is zero.
Since measuring the offset error on a DAC is such a
common task, a method is needed to reliably measure the
offset error of the DAC7611. This can easily be done as
shown in Figure 5. The resistor between V
OUT
and a nega-
tive voltage provides the output amplifier some ability to
swing below ground.
FIGURE 4. Suggested Power and Ground Connections for a DAC7611 Sharing a +5V Supply with a Digital System.
FIGURE 5. Offset Error Measurement Circuit.
+
+5V
GND
100μF
Digital Circuits
+5V
GND
+5V
Power
Supply
Other
Analog
Components
V
DD
GND
DAC7611
+
10μF
0.1μF
Optional
1
2
3
4
8
7
6
5
V
OUT
GND
CLR
LD
V
DD
CS
CLK
SDI
DAC7611
+
0.1μF
10μF
+5V
R
i
≤
200μA
–V
相關PDF資料 |
PDF描述 |
|---|---|
| DAC7611UB | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7612 | Dual, 12-Bit Serial Input DIGITAL-TO-ANALOG CONVERTER |
| DAC7612UB | Dual, 12-Bit Serial Input DIGITAL-TO-ANALOG CONVERTER |
| DAC7612U | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7613 | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC7611U | 制造商:BURR-BROWN 功能描述:IC 12BIT DAC SMD 7611 SOIC8 |
| DAC7611U | 制造商:Texas Instruments 功能描述:IC DAC 12BIT 132KSPS SOIC-8 制造商:Texas Instruments 功能描述:IC, DAC, 12BIT, 132KSPS, SOIC-8 |
| DAC7611U/2K5 | 功能描述:數模轉換器- DAC 12-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7611U/2K5G4 | 功能描述:數模轉換器- DAC 12-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7611UB | 功能描述:數模轉換器- DAC 12-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。