- 您現在的位置：買賣IC網 > PDF目錄376558 > DAC56 Monolithic 16-Bit Resolution DIGITAL-TO-ANALOG CONVERTER PDF資料下載
參數資料
| 型號： | DAC56 |
| 英文描述： | Monolithic 16-Bit Resolution DIGITAL-TO-ANALOG CONVERTER |
| 中文描述： | 單片16位分辨率的數字模擬轉換器 |
| 文件頁數： | 4/5頁 |
| 文件大?。?/td> | 165K |
| 代理商： | DAC56 |
DAC56
4
OPERATING INSTRUCTIONS
The accuracy of a D/A converter is described by the transfer
function as shown in Figure 1. Digital input to analog output
converter relationships are shown in Table I. The errors in
the D/A converter are combinations of analog errors due to
the linear circuitry, matching and tracking properties of the
ladder and scaling networks, power supply rejection, and
reference errors. In summary, these errors consist of initial
errors including gain, offset, linearity, differential linearity,
and power supply sensitivity. Gain drift over temperature
rotates the line (Figure 1) about the bipolar zero point and
offset drift shifts the line left or right over the operating
temperature range. Most of the offset and gain drift is due to
the drift of the internal reference zener diode with tempera-
ture or time.
The converter is designed so that these drifts are in opposite
directions. This way the bipolar zero voltage is virtually
unaffected by variations in the reference voltage.
DIGITAL INPUT CODES
The DAC56 accepts serial input data (MSB first) in Binary
Two’s Complement form—Refer to Table I for input/output
relationships.
POWER SUPPLY CONNECTIONS
Power supply decoupling capacitors should be added as
shown in the Connection Diagram (Figure 2), for optimum
performance and noise rejection.
These capacitors (1
μ
F tantalum recommended) should be
connected as close as possible to the converter.
FIGURE 2. Connection Diagram.
MSB ERROR ADJUSTMENT (OPTIONAL)
Differential linearity error at all codes of the DAC56 is
guaranteed to meet specifications without an external adjust-
ment. However, if adjustment of the differential linearity
error at bipolar zero is desired, it can be trimmed essentially
to zero using the circuit as shown in Figure 3.
FIGURE 3. MSB Adjustment Circuit.
After allowing ample warm-up time (5 to 10 minutes) to
assure stable operation, select the input code FFFF
H
. Mea-
sure the output voltage using a 6-1/2 digit voltmeter and
record the measurement. Change the digital input code to
0000
. Adjust the 100k
potentiometer (TCR of 100ppm
per
°
C or less is recommended) to make the output voltage
read 1LSB more than the voltage reading of the previous
code (ex. 1LSB = 92
μ
V at FSR = 6V).
If the MSB adjustment circuit is not used, pins 14 and 15
should be left open.
FIGURE 1. Input vs Output for an Ideal Bipolar D/A
Converter.
DIGITAL INPUT
ANALOG OUTPUT
Binary Two’s
Complement (BTC)
Voltage (V),
V
OUT
Mode
Current (mA),
I
OUT
Mode
DAC Output
7FFF
H
8000
H
0000
H
FFFF
H
+ Full Scale
– Full Scale
Bipolar Zero
Zero –1LSB
+2.999908
–3.000000
0.000000
–0.000092
–0.999970
+1.000000
0.000000
+0.030500
μ
A
TABLE I. Digital Input to Analog Output Relationship.
470k
200k
100k
(1)
Trim 15
MSB Adjust 14
1 –V
S
NOTE: (1) 10-15 turns.
Gain
Drift
Offset
Drift
Bipolar
Zero
0111...1111
1000...0000
A
Digital Output
(+FSR/2) –1LSB
–FSR/2
All Bits
On
* See Table I for digital code definitions.
16-Bit
DAC Latch
16-Bit Serial
to Parallel
Conversion
Control
Logic and
Level
Shifting
Circuit
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
16-Bit
I
DAC
–5V
+5V
–5V
1μF
1μF
1μF
LCOM
–V
S
+V
L
NC
CLK
LE
Data
–V
L
+V
S
SJ
R
F
V
(±3.0V)
TRIM
MSB ADJ
I
OUT
Analog
Output
1μF
+5V
ACOM
NOTES:
= Analog Common
= Logic Common
相關PDF資料 |
PDF描述 |
|---|---|
| DAC600 | 12-Bit 256MHz Monolithic DIGITAL-TO-ANALOG CONVERTER |
| DAC600 | 12-Bit 256MHz Monolithic Dightal-To-Analog Converter(12位 256MHz單片D/A轉換器) |
| DAC650 | 12-Bit 500MHz DIGITAL-TO-ANALOG CONVERTER |
| DAC650JL | 12-Bit 500MHz DIGITAL-TO-ANALOG CONVERTER |
| DAC650KL | 12-Bit 500MHz DIGITAL-TO-ANALOG CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC-562C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:12-Bit Digital-to-Analog Converter |
| DAC-562M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:12-Bit Digital-to-Analog Converter |
| DAC5652 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL, 10-BIT 275 MSPS DIGITAL-TO-ANALOG CONVERTER |
| DAC5652A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL, 10-BIT 275 MSPS DIGITAL-TO-ANALOG CONVERTER |
| DAC5652AIPFB | 功能描述:數模轉換器- DAC 10B 275MSPS Dual DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。