- 您現在的位置：買賣IC網 > PDF目錄376557 > DAC2932PFBT DUAL 12-BIT 40MSPS DIGITAL TO ANALOG CONVERTER PDF資料下載
參數資料
| 型號： | DAC2932PFBT |
| 元件分類： | DAC |
| 英文描述： | DUAL 12-BIT 40MSPS DIGITAL TO ANALOG CONVERTER |
| 中文描述： | 雙通道12位40MSPS數模轉換器 |
| 文件頁數： | 18/24頁 |
| 文件大?。?/td> | 343K |
| 代理商： | DAC2932PFBT |
SBAS279C AUGUST 2003 REVISED OCTOBER 2004
www.ti.com
18
The DC gain for this circuit is equal to feedback resistor R
F
.
At high frequencies, the DAC output impedance (C
D1
, C
D2
)
produces a zero in the noise gain for the OPA2690 that can
cause peaking in the closed-loop frequency response. C
F
is
added across R
F
to compensate for this noise gain peaking.
To achieve a flat transimpedance frequency response, the
pole in each feedback network should be set to:
1
2 R
F
C
F
where GBP = gain bandwidth product of the op amp, which
gives a corner frequency f
3dB
of approximately:
GBP
4 R
F
C
F
f
3dB
GBP
2 R
F
C
D
The full-scale output voltage is simply defined by the
product of I
OUTFS
R
F
, and has a negative unipolar
excursion. To improve on the ac performance of this circuit,
adjustment of R
F
and/or I
OUTFS
should be considered.
Further extensions of this application example may
include adding a differential filter at the OPA2690 output
followed by a transformer, in order to convert to a
single-ended signal.
SINGLE-ENDED CONFIGURATION
Using a single load resistor connected to one of the DAC
outputs, a simple current-to-voltage conversion can be
accomplished. The circuit in Figure 32 shows a 250
resistor connected to I
OUT
. Therefore, with a nominal
output current of 2mA, the DAC produces a total signal
swing of 0V to 0.5V.
I
OUT
I
OUT
DAC2932
250
250
I
OUTFS
= 2mA
V
OUT
= 0V to +0.5V
Figure 32. Differential Output Configuration
Using an RF Transformer
Different load resistor values may be selected, as long as
the output compliance range is not exceeded. Additionally,
the output current (I
OUTFS
) and the load resistor can be
mutually adjusted to provide the desired output signal
swing and performance.
INTERFACING ANALOG QUADRATURE
MODULATORS
One of the main applications for the dual-channel DAC is
baseband I- and Q-channel transmission for digital
communications. In this application, the DAC is followed
by an analog quadrature modulator, modulating an IF
carrier with the baseband data, as shown in Figure 33.
Often, the input stages of these quadrate modulators
consist of npn-type transistors that require a dc bias (base)
voltage of > 0.8V.
I
OUT
1
I
OUT
1
I
OUT
2
I
OUT
2
DAC2932
Signal
Conditioning
I
IN
I
REF
Q
IN
Q
REF
∑
Quadrature Modulator
V
OUT
~ 0V
P
to 0.5V
P
V
IN
~ 0.6V
P
to 1.8V
P
RF
I
IN
I
REF
Figure 33. Generic Interface to a Quadrature Modulator. Signal conditioning (level shifting) may be
required to ensure correct dc common-mode levels at the input of the quadrature modulator.
(8)
(9)
相關PDF資料 |
PDF描述 |
|---|---|
| DAC312BR | 12-Bit Digital-to-Analog Converter |
| DAC312GBC | 12-Bit Digital-to-Analog Converter |
| DAC312FR | 12-Bit High Speed Multiplying D/A Converter |
| DAC312HP | 12-Bit High Speed Multiplying D/A Converter |
| DAC312HS | 12-Bit High Speed Multiplying D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC2932PFBTG4 | 功能描述:數模轉換器- DAC Dual 12-Bit 40MSPS RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC-2-CG | 制造商:Thomas & Betts 功能描述: |
| DAC2K5G4 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-Bit, Low-Power Digital-to-Analog Converter |
| DAC2KY | 制造商:BB 制造商全稱:BB 功能描述:Dual, 12-Bit, 125MSPS DIGITAL-TO-ANALOG CONVERTER |
| DAC312 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit High Speed Multiplying D/A Converter |
發布緊急采購，3分鐘左右您將得到回復。