- 您現在的位置：買賣IC網 > PDF目錄376556 > DAC2902 Dual, 12-Bit, 125MSPS DIGITAL-TO-ANALOG CONVERTER PDF資料下載
參數資料
| 型號： | DAC2902 |
| 英文描述： | Dual, 12-Bit, 125MSPS DIGITAL-TO-ANALOG CONVERTER |
| 中文描述： | 雙通道，12位，125Msps數字模擬轉換器 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 389K |
| 代理商： | DAC2902 |
DAC2902
SBAS167A
15
GROUNDING, DECOUPLING, AND
LAYOUT INFORMATION
Proper grounding and bypassing, short lead length, and the use
of ground planes are particularly important for high-frequency
designs. Multilayer PCBs are recommended for best perfor-
mance since they offer distinct advantages such as minimiza-
tion of ground impedance, separation of signal layers by
ground layers, etc.
The DAC2902 uses separate pins for its analog and digital
supply and ground connections. The placement of the decou-
pling capacitor should be such that the analog supply (+V
A
)
is bypassed to the analog ground (AGND), and the digital
supply bypassed to the digital ground (DGND). In most
cases 0.1μF ceramic chip capacitors at each supply pin are
adequate to provide a low impedance decoupling path. Keep
in mind that their effectiveness largely depends on the
proximity to the individual supply and ground pins. There-
fore, they should be located as close as physically possible
to those device leads. Whenever possible, the capacitors
should be located immediately under each pair of supply/
ground pins on the reverse side of the pc board. This layout
approach will minimize the parasitic inductance of compo-
nent leads and PCB runs.
Further supply decoupling with surface-mount tantalum ca-
pacitors (1μF to 4.7μF) may be added as needed in proxim-
ity of the converter.
Low noise is required for all supply and ground connections
to the DAC2902. It is recommended to use a multilayer PCB
utilizing separate power and ground planes. Mixed signal
designs require particular attention to the routing of the
different supply currents and signal traces. Generally, analog
supply and ground planes should only extend into analog
signal areas, such as the DAC output signal and the refer-
ence signal. Digital supply and ground planes must be
confined to areas covering digital circuitry, including the
digital input lines connecting to the converter, as well as the
clock signal. The analog and digital ground planes should be
joined together at one point underneath the DAC. This can
be realized with a short track of approximately 1/8" (3mm).
The power to the DAC2902 should be provided through the
use of wide PCB runs or planes. Wide runs will present a
lower trace impedance, further optimizing the supply decou-
pling. The analog and digital supplies for the converter
should only be connected together at the supply connector of
the pc board. In the case of only one supply voltage being
available to power the DAC, ferrite beads along with bypass
capacitors may be used to create an LC filter. This will
generate a low-noise analog supply voltage that can then be
connected to the +V
A
supply pin of the DAC2902.
While designing the layout, it is important to keep the analog
signal traces separated from any digital line, in order to
prevent noise coupling onto the analog signal path.
相關PDF資料 |
PDF描述 |
|---|---|
| DAC2902-EVM | Dual, 12-Bit, 125MSPS DIGITAL-TO-ANALOG CONVERTER |
| DAC2900-EVM | DAC2900 10-bit, 125MSPS DC EVM(DAC2900 10位, 125MSPS DC 評估板) |
| DAC2902-EVM | DAC2902 12-bit, 125MSPS DC EVM(DAC2902 12位, 125MSPS DC 評估板) |
| DAC2904-EVM | DAC2904 14-bit, 125MSPS DC EVM(DAC2904 14位, 125MSPS DC 評估板) |
| DAC2932PFBTG4 | DUAL 12-BIT 40MSPS DIGITAL TO ANALOG CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC2902-EVM | 功能描述:數據轉換 IC 開發工具 DAC2902 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| DAC2902Y | 制造商:BB 制造商全稱:BB 功能描述:Dual, 12-Bit, 125MSPS DIGITAL-TO-ANALOG CONVERTER |
| DAC2902Y/1K | 功能描述:數模轉換器- DAC Dual 12-Bit 125Msps RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC2902Y/1KG4 | 功能描述:數模轉換器- DAC Dual 12-Bit 125Msps RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC2902Y/250 | 功能描述:數模轉換器- DAC Dual 12-Bit 125Msps RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。