參數資料
型號: DAC10BX
英文描述: 10-Bit Digital-to-Analog Converter
中文描述: 10位數字到模擬轉換器
文件頁數: 2/14頁
文件大?。?/td> 262K
代理商: DAC10BX
Digital Interface
The DAC1054 has two interface modes a WRITE mode
and a READ mode The WRITE mode is used to convert a
10-bit digital input word into a voltage The READ mode is
used to read back the digital data that was sent to one or all
of the DACs The WRITE mode maximum clock rate is
10 MHz READ mode is limited to a 5 MHz maximum clock
rate These modes are selected by the appropriate setting
of the RDWR bit which is part of the instruction byte The
instruction byte precedes the data byte at the DI pin In both
modes a high level on the Start Bit (SB) alerts the DAC to
respond to the remainder of the input stream
Table I lists the instruction set for the WRITE mode when
writing to only a single DAC and Table II lists the instruction
set for a global write Bits A0 and A1 select the DAC to be
written to The DACs are always written to MSB first All
DACs will be written to sequentially if the global bit (G) is
high DAC 1 is written to first then DACs 2 3 and 4 (in that
order) For a global write bits A0 and A1 of the instruction
byte are not required (see
Figure 2 timing diagram) If the
update bit (U) is high then the DAC output(s) will be updat-
ed on the rising edge of CS otherwise the new data byte
will be placed only in the input register Chip Select (CS)
must remain low for at least one clock cycle after the last
data bit has been entered (See
Figures 1 and 2 )
When the U bit is set low an asynchronous update of all the
DAC outputs can be achieved by taking AU low The con-
tents of the input registers are loaded into the DAC regis-
ters with the update occurring on the falling edge of AU CS
must be held high during an asynchronous update
All DAC registers will have their contents reset to all zeros
on power up
TABLE I WRITE Mode Instruction Set (Writing to a Single DAC)
SB
RDWR
G
U
A1
A0
Description
Bit
1
Bit
2
Bit
3 Bit
4 Bit
5 Bit
6
1
0
0000
Write DAC 1 no update of DAC outputs
1
0
0001
Write DAC 2 no update of DAC outputs
1
0
0010
Write DAC 3 no update of DAC outputs
1
0
0011
Write DAC 4 no update of DAC outputs
1
0
0100
Write DAC 1 update DAC 1 on CS rising edge
1
0
0101
Write DAC 2 update DAC 2 on CS rising edge
1
0
0110
Write DAC 3 update DAC 3 on CS rising edge
1
0
0111
Write DAC 4 update DAC 4 on CS rising edge
TABLE II WRITE Mode Instruction Set (Writing to all DACs)
SB
RDWR
GU
Description
Bit
1
Bit
2
Bit
3
Bit
4
1
0
1
0
Write all DACs no update of outputs
1
0
1
Write all DACs update all outputs on CS rising edge
10
相關PDF資料
PDF描述
DAC1220LJ 12-Bit Digital-to-Analog Converter
DAC1222LJ 12-Bit Digital-to-Analog Converter
DAC1350X DAC1350X 10BIT 75MSPS Quad-DAC|Data Sheet
DAC1353X DAC1353X 1.2V 8BIT 2MSPS DAC|Data Sheet
DAC1391X DAC1391X 2.5V 12BIT 80MSPS DAC|Data Sheet
相關代理商/技術參數
參數描述
DAC-10BX/883 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10-Bit Digital-to-Analog Converter
DAC10BX/883C 制造商:Analog Devices 功能描述:DAC 1-CH Current Steering 10-bit 18-Pin CDIP Tube
DAC-10-CG 制造商:Thomas & Betts 功能描述:4IN DPAC CBODY W/ CV & GASKET
DAC10FX 功能描述:IC DAC 10BIT MULT HS 85NS 18CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散(最大):100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC(J 形引線) 供應商設備封裝:28-PLCC(11.51x11.51) 包裝:帶卷 (TR) 輸出數目和類型:1 電壓,單極;1 電壓,雙極 采樣率(每秒):143k
DAC10GP 功能描述:IC DAC 10BIT MULTIPLY HS 18-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*