參數資料
型號: DAC1008D650HN
廠商: NXP SEMICONDUCTORS
元件分類: DAC
英文描述: Dual 10-bit DAC; up to 650 Msps; 2×, 4× or 8× interpolating
中文描述: 10-BIT DAC, PQCC64
封裝: 9 X 9 MM, 0.85 MM HEIGHT, PLASTIC, SOT804-3, VQFN-64
文件頁數: 15/98頁
文件大?。?/td> 551K
代理商: DAC1008D650HN
DAC1008D650
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 17 December 2010
15 of 98
NXP Semiconductors
DAC1008D650
2
×
, 4
×
or 8
×
interpolating DAC with JESD204A
10.2.4
Descrambler
The descrambler is a 16-bit parallel self-synchronous descrambler based on the
polynomial 1 + x
14
+ x
15
. This processing can be turned off.
10.2.5
Inter-lane alignment
This feature removes strict PCB design skew compensation between the lanes.
10.2.5.1
Single device operation
This module handles the alignment of the four data streams. Because of inter-lane skew
and each PLL per lane concept, these alignment characters may be received at different
times by the receivers. After the synchronization period, the lock signal will be HIGH. This
enables the receipt of K28.3 /A/ characters.
The ILA_CNTRL register’s SEL_ILA[1:0] bits select which K28.3 /A/ symbol triggers the
initial lane alignment:“00” = 1st /A/ symbol, “01” = 2nd /A/ symbol, “10” = 3rd /A/ symbol,
“11” = 4th /A/ symbol;
Table 86 on page 61
. When all receivers have received their first
selected /A/, they start propagating the received data to the frame assembly module at the
same point in time.
This module can compensate for up to
±
7 frame clock period misalignments between the
lanes.
When initial lane alignment is not supported, the manual alignment mode can be used.
After the initial ILA sequence, the lane alignment monitoring starts. If the received user
data contains a K28.3 /A/ symbol:
its position is compared to the value of the alignment monitor counter
if two successive K28.3 /A/ symbols have been received at a wrong position, a
realignment takes place
if the buffers are empty or overflow, this is indicated by the registers
ILA_BUF_ERR_LN0 to ILA_BUF_ERR_LN3
10.2.5.2
Multi-device operation
DAC1008D650 implements a multi-device inter-lane alignment that guarantees a skew of
less than one output period between them.
Two modes are available: master/slave and all slave. Both make use of the MDS_P and
MDS_N pins.
相關PDF資料
PDF描述
DAC1008D650HN Dual 10-bit DAC; up to 650 Msps; 2×, 4× or 8× interpolating
DAC1008D750HN Dual 10-bit DAC; up to 750 Msps; 2×, 4× or 8× interpolating
DAC1008D750HN Dual 10-bit DAC; up to 750 Msps; 2×, 4× or 8× interpolating
DAC1208D650HN Dual 12-bit DAC; up to 650 Msps; 2×, 4× or 8× interpolating
DAC1208D650HN Dual 12-bit DAC; up to 650 Msps; 2×, 4× or 8× interpolating
相關代理商/技術參數
參數描述
DAC1008D650HN/C1,5 功能描述:數模轉換器- DAC DL 10BIT DAC 650MSPS 2X 4X OR 8X INT RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
DAC1008D650HN-C1 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
DAC1008D750 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual 10-bit DAC up to 750 Msps 2×, 4× or 8× interpolating with JESD204A interface
DAC1008D750_11 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual 10-bit DAC; up to 750 Msps; 2×, 4× or 8× interpolating