- 您現在的位置：買賣IC網 > PDF目錄237623 > D4N-3172 SNAP ACTING/LIMIT SWITCH, DPST, MOMENTARY, 2.5A, 250VDC, 9mm, PANEL MOUNT PDF資料下載
參數資料
| 型號： | D4N-3172 |
| 元件分類： | 開關 |
| 英文描述： | SNAP ACTING/LIMIT SWITCH, DPST, MOMENTARY, 2.5A, 250VDC, 9mm, PANEL MOUNT |
| 文件頁數： | 11/24頁 |
| 文件大小： | 6206K |
| 代理商： | D4N-3172 |
D4N
19
Wiring
When connecting to the terminals via insulating tube and M3.5
crimp terminals, arrange the crimp terminals as shown below so
that they do not rise up onto the case or the cover.
Applicable lead wire size: AWG20 to AWG18 (0.5 to 0.75 mm2).
Use lead wires of an appropriate length, as shown below. Not
doing so may result in excess length causing the cover to rise and
not fit properly.
One-conduit Type (3 Poles)
Two-conduit Type (3 Poles)
Do not push crimp terminals into gaps in the case interior. Doing so
may cause damage or deformation of the case.
Use crimp terminals not more than 0.5 mm in thickness. Otherwise,
they will interfere with other components inside the case.
[Reference] The crimp terminals shown below are not more than
0.5 mm thick.
Contact Arrangement
The contact arrangements are shown below.
Screw Terminal Type
Connector Type
Applicable socket: XS2F-D421 series (OMRON).
Refer to the Connector Catalog for details on socket pin numbers
and lead wire colors.
Socket Tightening (Connector Type)
Turn the socket connector screws by hand and tighten until no
space remains between the socket and the plug.
Make sure that the socket connector is tightened securely.
Otherwise, the rated degree of protection (IP67) may not be
maintained and vibration may loosen the socket connector.
Conduit Opening
Connect a recommended connector to the opening of the conduit
and tighten the connector to the specified torque. The case may be
damaged if an excessive tightening torque is applied.
When using 1/2-14NPT, wind sealing tape around the joint
between the connector and conduit opening so that the enclosure
will conform to IP67.
Use a cable with a suitable diameter for the connector.
Attach and tighten a conduit cap to the unused conduit opening
when wiring. Tighten the conduit cap to the specified torque. The
conduit cap is provided with the Switch (2-conduit types).
Changing the Lever
The lever mounting screws can be used to set the lever position to
any position in a 360
° angle at 7.5° increments. Grooves are incised
on the lever and rotary shaft that engage to prevent the lever from
slipping against the rotary shaft. The screws on adjustable roller lever
models can also loosened to change the length of the lever.
Remove the screws from the front of the lever before mounting the
lever in reverse (front/back), and set the level so that operation will be
completed before exceeding a range of 180
° on the horizontal.
Manufacturer
Type
J.S.T. Mfg. Co.
FN0.5-3.7 (F Type)
N0.5-3.7 (Straight Type)
22
21
34
33
12
11
A
C
E
B
D
F
C
E
B
D
F
28 mm
Tolerance
±2 mm
33 mm
42 mm
22
21
34
33
12
11
A
C
E
B
D
F
A
C
E
BD F
28 mm
Tolerance
±2 mm
Left hand
42 mm
A
C
E
BD F
28 mm
Tolerance
±2 mm
Right hand
42 mm
L
l
F
B
D dia.
dz dia.
Correct
Incorrect
Terminal screw
Crimp terminal
t:
0.5 mm
dz dia.:
3.7 mm
D dia.:
2.9 mm
B:
6.6 mm
L:
19 mm
F:
7.7 mm
I :
8.0 mm
14
32
13
31
D4N-
@D@@ (3NC)
11
21
12
22
31
32
D4N-
@B@@ (2NC)
D4N-
@2@@ (2NC (SNAP))
11
31
12
32
D4N-
@C@@ (2NC/1NO)
D4N-
@F@@ (2NC/1NO (MBB))
D4N-
@A@@ (1NC/1NO)
D4N-
@E@@ (1NC/1NO (MBB))
33
34
11
21
12
22
11
33
12
34
D4N-
@1@@ (1NC/1NO (SNAP))
14 (4)
32 (2)
(3) 13
(1) 31
1
3
24
Pin No. (Terminal No.)
D4N-9B
@@ (2NC)
D4N-92
@@ (2NC (SNAP))
D4N-9A
@@ (1NC/1NO)
D4N-9E
@@ (1NC/1NO (MBB))
(1) 11
(3) 31
12 (2)
32 (4)
(1) 11
(3) 33
12 (2)
34 (4)
D4N-91
@@ (1NC/1NO (SNAP))
相關PDF資料 |
PDF描述 |
|---|---|
| D4N-6F20 | SNAP ACTING/LIMIT SWITCH, 3PST, MOMENTARY, 2.5A, 250VDC, PANEL MOUNT |
| D4N-8E32 | SNAP ACTING/LIMIT SWITCH, DPST, MOMENTARY, 2.5A, 250VDC, 6mm, PANEL MOUNT |
| D4N-9B20 | SNAP ACTING/LIMIT SWITCH, DPST, MOMENTARY, 2.5A, 250VDC, PANEL MOUNT |
| D101J12S117PQA | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
| D101J13B202PQA | ROCKER SWITCH, SPDT, LATCHED, THROUGH HOLE-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| D4N3187 | 制造商:Omron Corporation 功能描述: |
| D4N-3187 | 制造商:Omron Corporation 功能描述:D4N-3187, 1NC+1NO, plastic rod, 1/2 in. NPT 制造商:Omron Corporation 功能描述:Switch |
| D4N-3220 | 制造商:Omron Electronic Components LLC 功能描述:Switch, Safety Limit,2NC contacts, Snap Action, Roller Lever |
| D4N322G | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SW SAFETY ADJUST ROLLER LEVER |
| D4N-322G | 功能描述:基本/快動開關 Limit Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
發布緊急采購，3分鐘左右您將得到回復。