- 您現在的位置：買賣IC網 > PDF目錄379101 > CYV15G0403DXB-BGC (CYPRESS SEMICONDUCTOR CORP) Independent Clock Quad HOTLink II⑩ Transceiver PDF資料下載
參數資料
| 型號： | CYV15G0403DXB-BGC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Independent Clock Quad HOTLink II⑩ Transceiver |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封裝： | 27 X 27 MM, 1.57 MM HEIGHT, BGA-256 |
| 文件頁數： | 37/45頁 |
| 文件大?。?/td> | 517K |
| 代理商： | CYV15G0403DXB-BGC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
CYP15G0403DXB
CYV15G0403DXB
CYW15G0403DXB
Document #: 38-02065 Rev. *F
Page 37 of 45
X3.230 Codes and Notation Conventions
Information transmitted over a serial link is encoded eight bits
at a time into a 10-bit Transmission Character and then sent
serially, bit by bit. Information received over a serial link is
collected ten bits at a time, and those Transmission
Characters that are used for data characters are decoded into
the correct eight-bit codes. The 10-bit Transmission Code
supports all 256 8-bit combinations. Some of the remaining
Transmission Characters (Special Characters) are used for
functions other than data transmission.
The primary use of a Transmission Code is to improve the
transmission characteristics of a serial link. The encoding
defined by the Transmission Code ensures that sufficient
transitions are present in the serial bit stream to make clock
recovery possible at the Receiver. Such encoding also greatly
increases the likelihood of detecting any single or multiple bit
errors that may occur during transmission and reception of
information. In addition, some Special Characters of the Trans-
mission Code selected by Fibre Channel Standard contain a
distinct and easily recognizable bit pattern that assists the
receiver in achieving character alignment on the incoming bit
stream.
Notation Conventions
The documentation for the 8B/10B Transmission Code uses
letter notation for the bits in an 8-bit byte. Fibre Channel
Standard notation uses a bit notation of A, B, C, D, E, F, G, H
for the 8-bit byte for the raw 8-bit data, and the letters a, b, c,
d, e, i, f, g, h, j for encoded 10-bit data. There is a correspon-
dence between bit A and bit a, B and b, C and c, D and d, E
and e, F and f, G and g, and H and h. Bits i and j are derived,
respectively, from (A,B,C,D,E) and (F,G,H).
The bit labeled A in the description of the 8B/10B Transmission
Code corresponds to bit 0 in the numbering scheme of the
FC-2 specification, B corresponds to bit 1, as shown below.
FC-2 bit designation—
HOTLink D/Q designation— 7
8B/10B bit designation—
To clarify this correspondence, the following example shows
the conversion from an FC-2 Valid Data Byte to a Transmission
Character.
FC-2
45H
Bits: 7654 3210
7
6
6
5
5
4
4
E
3
3
D C B
2
2
1
1
0
0
A
H G F
0100 0101
Converted to 8B/10B notation, note that the order of bits has
been reversed):
Data Byte Name
D5.2
Bits: ABCDE FGH
10100 010
Translated to a transmission Character in the 8B/10B Trans-
mission Code:
Bits: abcdei fghj
101001 0101
Each valid Transmission Character of the 8B/10B Trans-
mission Code has been given a name using the following
convention: cxx.y, where c is used to show whether the Trans-
mission Character is a Data Character (c is set to D, and SC/D
= LOW) or a Special Character (c is set to K, and SC/D =
HIGH). When c is set to D, xx is the decimal value of the binary
number composed of the bits E, D, C, B, and A in that order,
and the y is the decimal value of the binary number composed
of the bits H, G, and F in that order. When c is set to K, xx and
y are derived by comparing the encoded bit patterns of the
Special Character to those patterns derived from encoded
Valid Data bytes and selecting the names of the patterns most
similar to the encoded bit patterns of the Special Character.
Under the above conventions, the Transmission Character
used for the examples above, is referred to by the name D5.2.
The Special Character K29.7 is so named because the first six
bits (abcdei) of this character make up a bit pattern similar to
that resulting from the encoding of the unencoded 11101
pattern (29), and because the second four bits (fghj) make up
a bit pattern similar to that resulting from the encoding of the
unencoded 111 pattern (7).
Note
. This definition of the 10-bit Transmission Code is based
on the following references, which describe the same 10-bit
transmission code.
A.X. Widmer and P.A. Franaszek. “A DC-Balanced, Parti-
tioned-Block, 8B/10B Transmission Code” IBM Journal of
Research and Development, 27, No. 5: 440-451 (September,
1983).
U.S. Patent 4,486,739. Peter A. Franaszek and Albert X.
Widmer. “Byte-Oriented DC Balanced (0.4) 8B/10B Parti-
tioned Block Transmission Code” (December 4, 1984).
Fibre Channel Physical and Signaling Interface (ANS
X3.230-1994 ANSI FC-PH Standard).
IBM Enterprise Systems Architecture/390 ESCON I/O
Interface (document number SA22-7202).
8B/10B Transmission Code
The following information describes how the tables are used
for both generating valid Transmission Characters (encoding)
and checking the validity of received Transmission Characters
(decoding). It also specifies the ordering rules followed when
transmitting the bits within a character and the characters
within any higher-level constructs specified by a standard.
Transmission Order
Within the definition of the 8B/10B Transmission Code, the bit
positions of the Transmission Characters are labeled a, b, c,
d, e, i, f, g, h, j. Bit “a” is transmitted first followed by bits b, c,
d, e, i, f, g, h, and j in that order.
Note that bit i is transmitted between bit e and bit f, rather than
in alphabetical order.
Valid and Invalid Transmission Characters
The following tables define the valid Data Characters and valid
Special Characters (K characters), respectively. The tables
are used for both generating valid Transmission Characters
and checking the validity of received Transmission
Characters. In the tables, each Valid-Data-byte or
Special-Character-code entry has two columns that represent
two Transmission Characters. The two columns correspond to
the current value of the running disparity. Running disparity is
a binary parameter with either a negative (–) or positive (+)
value.
[+] Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| CYV15G0403DXB-BGI | Independent Clock Quad HOTLink II⑩ Transceiver |
| CYV15G0403DXB-BGXC | Independent Clock Quad HOTLink II⑩ Transceiver |
| CYV15G0403DXB-BGXI | Independent Clock Quad HOTLink II⑩ Transceiver |
| CYW15G0403DXB-BGC | Independent Clock Quad HOTLink II⑩ Transceiver |
| CYW15G0403DXB-BGI | Independent Clock Quad HOTLink II⑩ Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYV15G0403DXB-BGI | 功能描述:電信線路管理 IC Quad Indep Ch XCVR COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYV15G0403DXB-BGXC | 功能描述:電信線路管理 IC Quad Indep Ch HOTLink II XCVR RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYV15G0403DXB-BGXI | 制造商:Cypress Semiconductor 功能描述: |
| CYV15G0403TB | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II⑩ Serializer |
| CYV15G0403TB_09 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II Serializer |
發布緊急采購，3分鐘左右您將得到回復。