- 您現在的位置：買賣IC網 > PDF目錄379094 > CY7C43624 (Cypress Semiconductor Corp.) 256 x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(256 x36 x2 雙向同步先進先出帶總線匹配) PDF資料下載
參數資料
| 型號： | CY7C43624 |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | 256 x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(256 x36 x2 雙向同步先進先出帶總線匹配) |
| 中文描述： | 256 x36 x2雙向同步FIFO瓦特/總線匹配（256 x36 x2雙向同步先進先出帶總線匹配） |
| 文件頁數： | 29/37頁 |
| 文件大?。?/td> | 581K |
| 代理商： | CY7C43624 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
CY7C43624
CY7C43634/CY7C43644
CY7C43664/CY7C43684
29
PRELIMINARY
select inputs must be HIGH during the LOW-to-HIGH transition
of its Master Reset input (MRS1 and MRS2). For example, to
load the preset value of 64 into X1 and Y1, SPM, FS0 and FS1
must be HIGH when FIFO1 reset (MRS1) returns HIGH. Flag-
offset registers associated with FIFO2 are loaded with one of
the preset values in the same way with Master Reset (MRS2).
When using one of the preset values for the flag offsets, the
FIFOs can be reset simultaneously or at different times.
To program the X1, X2, Y1, and Y2 registers from Port A, per-
form a Master Reset on both FIFOs simultaneously with SPM
HIGH and FS0 and FS1 LOW during the LOW-to-HIGH tran-
sition of MRS1 and MRS2. After this reset is complete, the first
four writes to FIFO1 do not store data in RAM but load the
offset registers in the order Y1, X1, Y2, X2. The Port A data
inputs used by the offset registers are (A
0
–
7
), (A
0
–
8
), (A
0
–
9
),
(A
0
–
11
), or (A
0
–
13
), for the CY7C436X4, respectively. The high-
est numbered input is used as the most significant bit of the
binary number in each case. Valid programming values for the
registers range from 1 to 252 for the CY7C43624; 1 to 508 for
the CY7C43634; 1 to 1012 for the CY7C43644; 1 to 4092 for
the CY7C43664; 1 to 16380 for the CY7C43684. After all the
offset registers are programmed from Port A, the Port B Full/
Input Ready (FFB/IRB) is set HIGH and both FIFOs begin nor-
mal operation.
To program the X1, X2, Y1, and Y2 registers serially, initiate a
Master Reset with SPM LOW, FS0/SD LOW, and FS1/SEN
HIGH during the LOW-to-HIGH transition of MRS1 and MRS2.
After this reset is complete, the X and Y register values are
loaded bit-wise through the FS0/SD input on each LOW-to-
HIGH transition of CLKA that the FS1/SEN input is LOW. Thir-
ty, thirty-six, forty, forty-eight, or fifty-six bit writes are needed
to complete the programming for the CY7C436X4, respective-
ly. The four registers are written in the order Y1, X1, Y2, and,
finally, X2. The first-bit write stores the most significant bit of
the Y1 register and the last-bit write stores the least significant
bit of the X2 register. Each register value can be programmed
from 1 to 252 (CY7C43624), 1 to 508 (CY7C43634), 1 to 1020
(CY7C43644), 1 to 4092 (CY7C43664), or 1 to 16380
(CY7C43684).
When the option to program the offset registers serially is cho-
sen, the Port A Full/Input Ready (FFA/IRA) flag remains LOW
until all register bits are written. FFA/IRA is set HIGH by the
LOW-to-HIGH transition of CLKA after the last bit is loaded to
allow normal FIFO1 operation. The Port B Full/Input ready
(FFB/IRB) flag also remains LOW throughout the serial pro-
gramming process, until all register bits are written. FFB/IRB
is set HIGH by the LOW-to-HIGH transition of CLKB after the
last bit is loaded to allow normal FIFO2 operation.
SPM, FS0/SD, and FS1/SEN function the same way in both
CY Standard and FWFT modes.
FIFO Write/Read Operation
The state of the Port A data (A
0
–
35
) lines is controlled by Port
A Chip Select (CSA) and Port A Write/Read Select (W/RA).
The A
0
–
35
lines are in the high-impedance state when either
CSA or W/RA is HIGH. The A
0
–
35
lines are active outputs
when both CSA and W/RA are LOW.
Data is loaded into FIFO1 from the A
0
–
35
inputs on a LOW-to-
HIGH transition of CLKA when CSA is LOW, W/RA is HIGH,
ENA is HIGH, MBA is LOW, and FFA/IRA is HIGH. Data is read
from FIFO2 to the A
0
–
35
outputs by a LOW-to-HIGH transition
of CLKA when CSA is LOW, W/RA is LOW, ENA is HIGH, MBA
is LOW, and EFA/ORA is HIGH (see
Table 2
). FIFO reads and
writes on Port A are independent of any concurrent Port B
operation.
The Port B control signals are identical to those of Port A with
the exception that the Port B Write/Read select (W/RB) is the
inverse of the Port A Write/Read select (W/RA). The state of
the Port B data (B
0
–
35
) lines is controlled by the Port B Chip
Select (CSB) and Port B Write/Read select (W/RB). The B
0
–
35
lines are in the high-impedance state when either CSB is
HIGH or W/RB is LOW. The B
0
–
35
lines are active outputs
when CSB is LOW and W/RB is HIGH.
Data is loaded into FIFO2 from the B
0
–
35
inputs on a LOW-to-
HIGH transition of CLKB when CSB is LOW, W/RB is LOW,
ENB is HIGH, MBB is LOW, and FFB/IRB is HIGH. Data is read
from FIFO1 to the B
0
–
35
outputs by a LOW-to-HIGH transition
of CLKB when CSB is LOW, W/RB is HIGH, ENB is HIGH,
MBB is LOW, and EFB/ORB is HIGH (see
Table 3
). FIFO reads
and writes on Port B are independent of any concurrent Port
A operation.
The set-up and hold time constraints to the port clocks for the
port Chip Selects and Write/Read selects are only for enabling
write and read operations and are not related to high-
impedance control of the data outputs. If a port enable is LOW
during a clock cycle, the port
’
s Chip Select and Write/Read
select may change states during the set-up and hold time win-
dow of the cycle.
When operating the FIFO in FWFT Mode and the Output
Ready flag is LOW, the next word written is automatically sent
to the FIFO
’
s output register by the LOW-to-HIGH transition of
the port clock that sets the Output Ready flag HIGH, data re-
siding in the FIFO
’
s memory array is clocked to the output reg-
ister only when a read is selected using the port
’
s Chip Select,
Write/Read select, Enable, and Mailbox select.
When operating the FIFO in CY Standard mode, regardless of
whether the Empty Flag is LOW or HIGH, data residing in the
FIFO
’
s memory array is clocked to the output register only
when a read is selected using the port
’
s Chip Select, Write/
Read select, Enable, and Mailbox select.
Synchronized FIFO Flags
Each FIFO is synchronized to its port clock through at least
two flip-flop stages. This is done to improve flag-signal reliabil-
ity by reducing the probability of the metastable events when
CLKA and CLKB operate asynchronously to one another. EFA/
ORA, AEA, FFA/IRA, and AFA are synchronized to CLKA.
EFB/ORB, AEB, FFB/IRB, and AFB are synchronized to
CLKB.
Table 4
and
Table 5
show the relationship of each port
flag to FIFO1 and FIFO2.
Empty/Output Ready Flags (EFA/ORA, EFB/ORB)
These are dual-purpose flags. In the FWFT Mode, the Output
Ready (ORA, ORB) function is selected. When the Output
Ready flag is HIGH, new data is present in the FIFO output
register. When the Output ready flag is LOW, the previous data
word is present in the FIFO output register and attempted
FIFO reads are ignored.
In the CY Standard mode, the Empty Flag (EFA, EFB) function
is selected. When the Empty Flag is HIGH, data is available in
the FIFO
’
s RAM memory for reading to the output register.
When Empty Flag is LOW, the previous data word is present
in the FIFO output register and attempted FIFO reads are ig-
nored.
The Empty/Output Ready flag of a FIFO is synchronized to the
port clock that reads data from its array. For both the FWFT
and CY Standard modes, the FIFO read pointer is increment-
ed each time a new word is clocked to its output register. The
state machine that controls an Output Ready flag monitors a
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C43644 | 1K x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(1K x36 x2 雙向同步先進先出帶總線匹配) |
| CY7C43664 | 4K x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(4K x36 x2 雙向同步先進先出帶總線匹配) |
| CY7C43684 | 16K x36 x2 Bidirectional Synchronous FIFO w/ Bus Matching(16K x36 x2 雙向同步先進先出帶總線匹配) |
| CY7C43636 | 512 x36/x18x2 Tri Bus FIFO(512 x36/x18x2 三路總線 先進先出) |
| CY7C43626 | 256 x36/x18x2 Tri Bus FIFO(256 x36/x18x2 三路總線先進先出) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C43642-10AC | 制造商:Cypress Semiconductor 功能描述:FIFO Mem Sync Dual Depth/Width Bi-Dir 1K x 36 x 2 120-Pin TQFP |
| CY7C43643-15AC | 制造商:Cypress Semiconductor 功能描述:FIFO Mem Sync Dual Depth/Width Uni-Dir 1K x 36 128-Pin TQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CY7C43643AV-10AC | 制造商:Cypress Semiconductor 功能描述:FIFO Mem Sync Dual Depth/Width Uni-Dir 1K x 36 128-Pin TQFP |
| CY7C43643AV-15AC | 制造商:Cypress Semiconductor 功能描述:FIFO Mem Sync Dual Depth/Width Uni-Dir 1K x 36 128-Pin TQFP |
| CY7C43643AV-7AC | 制造商:Cypress Semiconductor 功能描述:FIFO Mem Sync Dual Depth/Width Uni-Dir 1K x 36 128-Pin TQFP |
發布緊急采購，3分鐘左右您將得到回復。