- 您現在的位置：買賣IC網 > PDF目錄9598 > CY28410OXC-2T (Silicon Laboratories Inc)IC CLOCK CK410 GRANTSDALE 56SSOP PDF資料下載
參數資料
| 型號： | CY28410OXC-2T |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 10/16頁 |
| 文件大小： | 0K |
| 描述： | IC CLOCK CK410 GRANTSDALE 56SSOP |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/頻率發生器 |
| PLL： | 是 |
| 主要目的： | Intel CPU 服務器 |
| 輸入： | 晶體 |
| 輸出： | HCSL，LVCMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:21 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 266MHz |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 56-SSOP |
| 包裝： | 帶卷 (TR) |
CY28410-2
........................Document #: 38-07747 Rev *.* Page 3 of 16
Frequency Select Pins (FS_A, FS_B, and FS_C)
Host clock frequency selection is achieved by applying the
appropriate logic levels to FS_A, FS_B, FS_C inputs prior to
VTT_PWRGD# assertion (as seen by the clock synthesizer).
Upon VTT_PWRGD# being sampled LOW by the clock chip
(indicating processor VTT voltage is stable), the clock chip
samples the FS_A, FS_B, and FS_C input values. For all logic
levels of FS_A, FS_B, and FS_C, VTT_PWRGD# employs a
one-shot functionality in that once a valid LOW on
VTT_PWRGD# has been sampled, all further VTT_PWRGD#,
FS_A, FS_B, and FS_C transitions will be ignored, except in
test mode.
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions, such as individual
clock output buffers, can be individually enabled or disabled.
The registers associated with the Serial Data Interface
initialize to their default setting upon power-up, and therefore
use of this interface is optional. Clock device register changes
are normally made upon system initialization, if any are
required. The interface cannot be used during system
operation for power management functions.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operations from the controller. For
block write/read operation, the bytes must be accessed in
sequential order from lowest to highest byte (most significant
bit first) with the ability to stop after any complete byte has
been transferred. For byte write and byte read operations, the
system controller can access individually indexed bytes. The
offset of the indexed byte is encoded in the command code,
as described in Table 2.
The block write and block read protocol is outlined in Table 3
while Table 4 outlines the corresponding byte write and byte
read protocol. The slave receiver address is 11010010 (D2h).
Table 1. Frequency Select Table FS_A, FS_B, and FS_C
FS_C
FS_B
FS_A
CPU
SRC
PCIF/PCI
REF0
DOT96
USB
MID
0
1
100 MHz
33 MHz
14.318 MHz
96 MHz
48 MHz
0
1
133 MHz
100 MHz
33 MHz
14.318 MHz
96 MHz
48 MHz
0
1
0
200 MHz
100 MHz
33 MHz
14.318 MHz
96 MHz
48 MHz
0
266 MHz
100 MHz
33 MHz
14.318 MHz
96 MHz
48 MHz
1
0
x
Hi-Z
1
0
REF/2
REF/8
REF/24
REF
1
REF/2
REF/8
REF/24
REF
Table 2. Command Code Definition
Bit
Description
7
0 = Block read or block write operation, 1 = Byte read or byte write operation
(6:0)
Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be
'0000000'
Table 3. Block Read and Block Write Protocol
Block Write Protocol
Block Read Protocol
Bit
Description
Bit
Description
1Start
1
Start
8:2
Slave address – 7 bits
8:2
Slave address – 7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
18:11
Command Code – 8 bits
18:11
Command Code – 8 bits
19
Acknowledge from slave
19
Acknowledge from slave
27:20
Byte Count – 8 bits
(Skip this step if I2C_EN bit set)
20
Repeat start
28
Acknowledge from slave
27:21
Slave address – 7 bits
36:29
Data byte 1 – 8 bits
28
Read = 1
37
Acknowledge from slave
29
Acknowledge from slave
45:38
Data byte 2 – 8 bits
37:30
Byte Count from slave – 8 bits
46
Acknowledge from slave
38
Acknowledge
相關PDF資料 |
PDF描述 |
|---|---|
| CY28410ZXCT | IC CLOCK CK410GRANTSDALE 56TSSOP |
| ISL4244EIR | IC 3DRVR/5RCVR RS232 3V 32-QFN |
| MS27472T24B4SA | CONN RCPT 56POS WALL MT W/SCKT |
| CY284108ZXCT | IC CLOCK SERV CK410B 56TSSOP |
| VE-22V-MX-F1 | CONVERTER MOD DC/DC 5.8V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY28410OXCT | 功能描述:時鐘發生器及支持產品 SysClk Intel Lakeprt & Grantsdale Chipset RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| CY28410ZC | 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:Clock Generator for Intel Grantsdale Chipset |
| CY28410ZCT | 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:Clock Generator for Intel Grantsdale Chipset |
| CY28410ZXC | 功能描述:時鐘發生器及支持產品 SysClk Intel Lakeprt & Grantsdale Chipset RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| CY28410ZXC-2 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Clock Generator for Intel Grantsdale Chipset |
發布緊急采購，3分鐘左右您將得到回復。