• <code id="75h1o"><label id="75h1o"><noframes id="75h1o"></noframes></label></code>
    <tfoot id="75h1o"><wbr id="75h1o"></wbr></tfoot>
      <menuitem id="75h1o"><dl id="75h1o"></dl></menuitem>
      參數資料
      型號: CY28354OXC-400
      廠商: Silicon Laboratories Inc
      文件頁數: 2/8頁
      文件大?。?/td> 0K
      描述: IC BUFF 273MHZ 4DDR DIMM 48SSOP
      標準包裝: 30
      類型: 扇出緩沖器(分配)
      PLL: 無
      主要目的: 存儲器,DDR
      輸入: 時鐘
      輸出: 時鐘
      電路數: 2
      比率 - 輸入:輸出: 1:12
      差分 - 輸入:輸出: 無/無
      頻率 - 最大: 400MHz
      電源電壓: 2.3 V ~ 2.7 V
      工作溫度: 0°C ~ 85°C
      安裝類型: *
      封裝/外殼: *
      供應商設備封裝: *
      包裝: *
      CY28354-400
      .......................... Document #: 38-07615 Rev. *B Page 2 of 8
      Serial Data Interface
      To enhance the flexibility and function of the clock synthesizer,
      a two-signal serial interface is provided. Through the Serial
      Data Interface, various device functions such as individual
      clock output buffers, etc., can be individually enabled or
      disabled. The registers associated with the Serial Data
      Interface initializes to their default setting upon power-up, and
      therefore use of this interface is optional. Clock device register
      changes are normally made upon system initialization, if any
      are required. The interface can also be used during system
      operation for power management functions.
      Data Protocol
      The clock driver serial protocol accepts Byte Write, Byte Read,
      Block Write, and Block Read operation from the controller. For
      Block Write/Read operation, the bytes must be accessed in
      sequential order from lowest to highest byte (most significant
      bit first) with the ability to stop after any complete byte has
      been transferred. For Byte Write and Byte Read operations,
      the system controller can access individual indexed bytes. The
      offset of the indexed byte is encoded in the command code,
      as described in Table 1. The Block Write and Block Read
      protocol is outlined in Table 2.The slave receiver address is
      D2/DC depending on the state of the ADDRSEL pin.
      Pin Description
      Pin
      Name
      PWR
      I/O
      Description
      11, 13, 19, 21, 38, 36,
      5, 7, 44, 42, 32, 30
      DDRA[0:5]T
      DDRB[0:5]T
      VDD2.5
      O
      Clock outputs. These outputs provide copies of BUF_INA and
      BUF_INB, respectively.
      12, 14, 20, 22, 37, 35,
      6, 8, 43, 41, 31, 29
      DDRA[0:5]C
      DDRB[0:5]C
      VDD2.5
      O
      Clock outputs. These outputs provide complementary copies of
      BUF_INA and BUF_INB, respectively.
      18,
      4
      BUF_INA,
      BUF_INB
      VDD2.5
      I
      PD
      Reference input from chipset. 2.5V input. Internal pull-down
      17,
      3
      FB_OUTA
      FB_OUTB
      VDD2.5
      O
      Feedback clock for chipset.
      45
      I2C_CS
      VDD2.5
      I
      PD
      CS for I2C allows for multiple devices to be connected with
      the same I2C address. Internal pull-down. See Table 1.
      46
      ADDR_SEL
      VDD2.5
      I
      PD
      Selects I2C Address D2/DC. Internal Pull-down
      25
      SCLK
      VDD2.5
      I
      PU
      SMBus clock input. Internal Pull-up
      26
      SDATA
      VDD2.5
      I/O
      PU
      SMBus data input. Internal Pull-up
      1, 10, 16, 23, 28, 33, 39, 48 VDD2.5
      2.5V voltage supply
      2, 9, 15, 24, 27, 34, 40, 47
      GND
      Ground
      Table 1. Command Code Definition
      Bit
      Description
      7
      0 = Block Read or Block Write operation
      1 = Byte Read or Byte Write operation
      (6:5)
      01 to address chip when I2C_CS = 0
      10 to address chip when I2C_CS = 1
      (4:0)
      Byte offset for Byte Read or Byte Write operation. For Block Read or Block Write operations, these bits should
      be '00000'
      相關PDF資料
      PDF描述
      CY28378OXC IC CLOCK CK408/TITAN 845 48SSOP
      CY284108ZXC IC CLOCK SERV CK410B 56TSSOP
      CY28410OXC-2 IC CLOCK CK410 GRANTSDALE 56SSOP
      CY28410OXC IC CLOCK CK410 GRANTSDALE 56SSOP
      CY28411ZXC IC CLOCK CK410M ALVISO 56TSSOP
      相關代理商/技術參數
      參數描述
      CY28354OXC-400T 功能描述:時鐘緩沖器 273MHz Output Buffer for 4 DDR DIMMs RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲(最大值): 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel
      CY28358 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:200-MHz Differential Clock Buffer/Driver
      CY28358OC 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:200-MHz Differential Clock Buffer/Driver
      CY28358OCT 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:200-MHz Differential Clock Buffer/Driver
      CY28359 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:273 MHz 6 Output Buffer for DDR400 DIMMS