參數資料
型號： CT2579
廠商： Aeroflex Inc.
英文描述： APPLICATION NOTE #108
文件頁數： 7/41頁
文件大小： 112K
代理商： CT2579
7
APPLICATION NOTE #108
Released 9/98
NSYNC
Signal to subsystem indicating receipt of a Synchronize mode commands If the mode
code has an associated data word, it will be available on T0-T15 at this time. If there
is no associated data word, T0-T15 will be zero.
NVCR
Early indication that a Command Word has been received and is being processed.
The Command Word received is available on the T0-15 bus for decoding at this time.
The user can use this signal for message illegalization and to set the RT Status bits.
NDATA
Access to valid data word in real time before being written to RAM. Data word
available on T0-T15 during active low signal.
NILLCMD
Input to illegalise a command to the Remote Terminal with a clear status response.
The signal is sampled after NVCR except non mode code receive commands in
which case it is sampled after the last data word has been received. A low on this
input will illegalise the message, Command will not be stored in the Command /
Status memory and no transfers to / from main RAM will take place. The device will
respond with a clear status unless a bit has been specifically set. No data will be
transmitted following status.
BC Discrete Signals
NNEWBUS
A Bus Control sequence may not normally be initiated until the current sequence is
completed, indicated by signal EOT. However, the Bus Control sequence may be
terminated and restarted if NNEWBUS is active low along with write to address 0 00
00 (000h). This feature would only be used in bus switching.
EOT
Indicates that a valid transfer has been completed on the bus selected.
1 = Valid transfer completed
0 = Not yet Completed
ERROR
Indication that an error has occurred either in the information transferred to the unit
from the subsystem or in the transfers on the 1553 data bus. Nature of error is
available by reading from register location 0 00 12 (012h).
1 = Error has occurred
0 = No error
NSTSTRB
This signal goes low for 8.5 uS to indicate a valid transfer has been completed on the
1553 data bus and the received Status word is now available on the T0-T15 highway.
The Status word is also stored in the Command / Status memory at this time. Once
the signal goes high data received by the Bus Controller (RT to BC transfer) will be
transferred to the main RAM from the 32 word data buffer memory. Note: Data
transferred in RT to RT transfers is not stored in the Bus Controllers main RAM.
NNINHST
May be used to illegalise a message just received. Signal can be tied to STATUS for
illegalisation due to 1760 checksum failures. A low will prevent any data received
being transferred to the main RAM, and the Status word will not be stored in the
Command / Status memory.
相關PDF資料
PDF描述
CT2581-02-IN-F84 CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2581-02-IN-P119 CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2581 CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2581-02-XT-F84 CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2578 CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
相關代理商/技術參數
參數描述
CT2580VY-SM 制造商:Panasonic Industrial Company 功能描述:MANUAL
CT2581 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2581-02-CG-F84 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2581-02-CG-P119 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
CT2581-02-IN-F84 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2578 / CT2581 SIMPLE REMOTE TERMINAL FOR MIL-STD-1553 / 1760 & McAir
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*