- 您現在的位置：買賣IC網 > PDF目錄369674 > CT2565-001-2 (Aeroflex Inc.) CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B PDF資料下載
參數資料
| 型號： | CT2565-001-2 |
| 廠商： | Aeroflex Inc. |
| 英文描述： | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| 中文描述： | CT2565總線控制器，遠程終端和總線監測的MIL - STD - 1553B總線 |
| 文件頁數： | 21/31頁 |
| 文件大小： | 356K |
| 代理商： | CT2565-001-2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Aeroflex Circuit Technology
21
SCDCT2565 REV B 8/10/99 Plainview NY (516) 694-6700
DYNAMIC BUS CONTROL (00000)
MESSAGE SEQUENCE = DBC * STATUS
The CT2565 responds with status. If the subsystem wants control of the bus, it must set DBACC within 2.5us after NBGRT.
ERROR CONDITIONS
1.
Invalid Command.
No response, command ignored.
2.
Command Followed by Data Word.
No status response. Bits set: message error (SW), High word Count (BIT Word).
3.
T/R bit Set to Zero.
No status response. Bits set: message error (SW), T/R Error (Bit Word).
4.
Zero T/R bit and Broadcast Address.
No status response. Bits set: message error, broadcast received (SW), Illegal Mode Code, T/R
Error (BIT Word).
5.
Broadcast Address.
No status response. Bits set: message error, broadcast received (SW), Illegal Mode Code (BIT Word).
SYNCHRONIZE WITHOUT DATA WORD (00001)
MESSAGE SEQUENCE = SYNC * STATUS
The CT2565 responds with status. If sent as a broadcast, the broadcast receive bit will be set and status response suppressed.
ERROR CONDITIONS
1.
Invalid Command.
No response, command ignored.
2.
Command Followed by Data Word.
No status response. Bits set: message error (SW), High Word Count (BIT Word).
3.
T/R bit Set to Zero.
No status response. Bits set: message error (SW), T/R Error (BIT Word).
4.
Zero T/R bit and Broadcast Address.
No status response. Bits set: message error, broadcast received (SW), Illegal Mode Code, T/R
Error (BIT Word).
TRANSMIT STATUS WORD (00010)
MESSAGE SEQUENCE = TRANSMIT STATUS * STATUS
The status and BIT word registers are not altered by this command and contain the resulting status from the previous command.
ERROR CONDITIONS
1.
Invalid Command.
No response, command ignored.
2.
Command Followed by Data Word.
No status response. Bits set: message error (SW), High Word Count (BIT Word).
3.
T/R bit Set to Zero.
No status response. Bits set: message error (SW), T/R Error (BIT Word).
4.
Zero T/R bit and Broadcast Address.
No status response. Bits set: message error, broadcast received (SW), Illegal Mode Code, T/R
Error (BIT Word).
5.
Broadcast Address.
No status response. Bits set: message error, broadcast received (S/W), Illegal Mode code, T/R Error (BIT Word).
INITIATE SELF-TEST (00011)
MESSAGE SEQUENCE = SELF TEST * STATUS
The CT2565 responds with a status word. If the command was broadcast, the broadcast received bit is set and status transmission
suppressed. Short-loop test is initiated on the status word transmitted. If the test fails, an RT fail flag is generated.
ERROR CONDITIONS
1.
Invalid Command.
No response, command ignored.
2.
Command Followed by Data Word.
No status response. Bits set: message error (SW), High Word Count (BIT Word).
3.
T/R bit Set to Zero.
No status response. Bits set: message error (SW), T/R Error (BIT Word).
4.
Zero T/R bit and Broadcast Address.
No status response. Bits set: message error, broadcast received (SW), T/R Error (BIT Word).
5.
Faulty Test.
Bits set: terminal flag (SW), A/B Loop Test Fail, Current 1553 Bus (A or B) Loop Test Fail (BIT Word).
TRANSMITTER SHUTDOWN (00100)
MESSAGE SEQUENCE - SHUTDOWN * STATUS
This command is only used with dual redundant bus systems. The CT2565 responds
with status. At the end of the status transmission, the CT2565 inhibits any further transmission from the dual redundant channel. Once
shutdown, the transmitter can only be re-activated by Override Transmitter Shutdown or RESET RT commands.
ERROR CONDITIONS
1.
Invalid Command.
No response, command ignored.
2.
Command Followed by Data Word.
No status response. Bits set: message error (SW), High Word Count (BIT Word).
3.
T/R bit Set to Zero.
No status response. Bits set: message error (SW), T/R Error BIT Word).
4.
Zero T/R bit and Broadcast Address.
No status response. Bits set: message error, broadcast received (SW), Illegal Mode Code, T/R
Error (BIT Word).
Table 8 – Mode Codes
相關PDF資料 |
PDF描述 |
|---|---|
| CT2565-201-1 | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-201-2 | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-FP | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2566 | CT2566 MIL-STD-1553 to Microprocessor Interface Unit |
| CT2566-FP | CT2566 MIL-STD-1553 to Microprocessor Interface Unit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CT2565-201-1 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-201-2 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-FP | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2566 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2566 MIL-STD-1553 to Microprocessor Interface Unit |
| CT25664AA1067 | 制造商:Crucial Technology 功能描述:DRAM Module DDR2 SDRAM 2Gbyte 240UDIMM 制造商:Micron Consumer Products Group 功能描述:2GB, 240-PIN DIMM, DDR2 PC2-850 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。