- 您現在的位置：買賣IC網 > PDF目錄369674 > CT2565-001-1 (Aeroflex Inc.) CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B PDF資料下載
參數資料
| 型號： | CT2565-001-1 |
| 廠商： | Aeroflex Inc. |
| 英文描述： | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| 中文描述： | CT2565總線控制器，遠程終端和總線監測的MIL - STD - 1553B總線 |
| 文件頁數： | 19/31頁 |
| 文件大小： | 356K |
| 代理商： | CT2565-001-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Aeroflex Circuit Technology
19
SCDCT2565 REV B 8/10/99 Plainview NY (516) 694-6700
NAME
Definition
GAP TIME
NODT low time. 2MHz Clock
allows 500ns increments to
128μs (remains static at FF on
overflow).
WORD TRANSFER
Logic "1" indicates successful
transfer to subsystem.
WORD TRANSFERRED
Indicates successful transfer
(See bit 7)
VALID WORD
Reset (1) indicates Manchester
error, Parity error, Low Bit Count
and/or Status sync field.
COMMAND SYNC
Logic "1" indicates Command or
Status sync field. Logic "0"
indicates data sync.
CHAN A/B
Logic "1" if word received on
1553 bus Channel B.
WORD GAP
Set (0) if current word was
received at least 2μs after
receipt of previous word (parity
to mid-sync).
Note: Subsystem should clear entire memory prior to start of MT
operation.
Figure 20 – Identification Word
MT Operation
In the MT mode, the CT2565 captures all valid
transmissions on both channels of the 1553 bus, allowing
the user to monitor bus activity. Each word is transferred to
the subsystem along with an identification for interpretation
of the 1553 data stream.
MT Initialization
Initialize the CT2565 for MT operation per Table 2. The
CT2565 will remain in an idle state until BCSTART (pin 41)
is pulsed low. Figure 21 illustrates MT operation.
Valid words received by the CT2565 are transferred to the
subsystem along with an identification Word by a single
DMA handshake with two memory-write operations shown
in Figure 22, MT Transfer Timing. Since the decoder will
reject words based on sync field errors and/or errors in the
first 2 non-sync bits, these words will not be processed
further (i.e., the subsystem will receive no indication of the
receipt of this word).
EYES
NO
YES
INCREMENT MEM ADDR
INCREMENT MEM ADDR
IDENTIFICATION WORD
MEMORY WRITE
DMA
NODT LOW
SYNC + 2 BITS
DECODER CHECK
ACTIVITY
1553 BUS
START MT OPERATION
(START-UP ONLY)
INITIALIZATION
START
1553 INPUT
MEMORY WRITE
15
8 7
0
GAP TIME
WORD TRANSFER
LOGIC "1"
LOGIC "1"
VALID WORD
COMMAND SYNC
CH A/B
WORD GAP
SET TO "0"
Figure 21 – MT Operation Flow Chart
Notes:
(1) Steps marked with " _ _ _" indicates operation is
transparent to user.
(2) Steps marked with " ___" indicates user interaction
required.
相關PDF資料 |
PDF描述 |
|---|---|
| CT2565 | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-001-2 | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-201-1 | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-201-2 | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-FP | CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CT2565-001-2 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-201-1 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-201-2 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565-FP | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2566 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2566 MIL-STD-1553 to Microprocessor Interface Unit |
發布緊急采購，3分鐘左右您將得到回復。