- 您現在的位置：買賣IC網 > PDF目錄369673 > CT1990-1-20 (Aeroflex Inc.) MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control PDF資料下載
參數資料
| 型號： | CT1990-1-20 |
| 廠商： | Aeroflex Inc. |
| 英文描述： | MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| 中文描述： | 符合MIL - STD - 1553B總線遠程終端，總線控制器，監視器或被動混合控制的狀態字 |
| 文件頁數： | 3/29頁 |
| 文件大?。?/td> | 232K |
| 代理商： | CT1990-1-20 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Aeroflex Circuit Technology
SCDCT1990 REV B 8/21/00 Plainview NY (516) 694-6700
3
REMOTE TERMINAL OPERATION
Receive Data Operation
All valid data words associated with a valid receive data command word for the RT are passed to the subsystem.
The RT examines all command words from the bus and will respond to valid (i.e. correct Manchester, parity
coding etc.) commands which have the correct RT address (or broadcast address if the RT broadcast option is
enabled). When the data words are received, they are decoded and checked by the RT and, if valid, passed to
the subsystem on a word by word basis at 20 μs intervals. This applies to receive data words in both Bus
Controller to RT and RT to RT messages. When the RT detects that the message has finished, it checks that the
correct number of words have been received and if the message is fully valid, then a Good Block Received
signal is sent to the subsystem, which must be used by the subsystem as permission to use the data just
received.
The subsystem must therefore have a temporary buffer store up to 32 words long into which these data words
can be placed. The Good Block Received signal will allow use of the buffer store data once the message has
been validated.
If a block of data is not validated, then Good Block Received will not be generated. This may be caused by any
sort of message error or by a new valid command for the RT being received on another bus to which the RT
must switch.
Transmit Data Operation
If the RT receives a valid transmit data command addressed to the RT, then the RT will request the data words
from the subsystem for transmission on a word by word basis. To allow maximum time for the subsystem to
collect each data word, the next word is requested by the RT as soon as the transmission of the current word
has commenced.
It is essential that the subsystem should provide all the data words requested by the RT once a transmit
sequence has been accepted. Failure to do so will be classed by the RT as a subsystem failure and reported as
such to the Bus Controller.
Control of Data Transfers
This section describes the detailed operation of the data transfer mechanism between the RT and subsystems.
It covers the operations of the signals DTRQ, DTAK, IUSTB, H/L, GBR, NBGT, TX/RX during receive data and
transmit data transfers.
Figure 7 shows the operation of the data handshaking signals during a receive command with two data words.
When the RT has fully checked the command word, NBGT is pulsed low, which can be used by the subsystem
as an initialization signal. TX/RX will be set low indicating a receive command. When the first data word has
been fully validated, DTRQ is set low. The subsystem must then reply within approximately 1.5 μs by setting
DTAK low. This indicates to the RT that the subsystem is ready to accept data. The data word is then passed to
the subsystem on the internal highway IH08-IH715 in two bytes using IUSTB as a strobe signal and H/L as the
byte indicator (high byte first followed by low byte). Data is valid about both edges of IUSTB. Signal timing for
this handshaking is shown in Figure 12.
If the subsystem does not declare itself busy, then it must respond to DTRQ going low by setting DTAK low
within approximately 1.5 us. Failure to do so will be classed by the RT as a subsystem failure and reported as
such to the Bus Controller.
It should be noted that IUSTB is also used for internal working in the RT. DTRQ being low should be used as an
enable for clocking data to the subsystem with IUSTB.
Once the receive data block has finished and been checked by the RT, GBR is pulsed low if the block is entirely
correct and valid. This is used by the subsystem as permission to make use of the data block. If no GBR signal
is generated, then an error has been detected by the RT and the entire data block is invalid and no data words in
it may be used.
If the RT is receiving data in an RT to RT transfer, the data handshaking signals will operate in an identical
fashion but there will be a delay of approx 70 μs between NBGT going low and DTRQ first going low. See
Figure 10.
相關PDF資料 |
PDF描述 |
|---|---|
| CT19901 | MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995 | MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995-20 | MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995-20-2 | MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995-20-3 | MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CT1990-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| CT1991-1-20 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995-20 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
| CT1995-20-2 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:MIL-STD-1553B Remote Terminal, Bus Controller, or Passive Monitor Hybrid with Status Word Control |
發布緊急采購，3分鐘左右您將得到回復。