- 您現在的位置：買賣IC網 > PDF目錄374172 > CS8441XN8 (ZF Electronics Corporation) 85mA Dual H-Bridge Odometer Driver with Divide by Select PDF資料下載
參數資料
| 型號： | CS8441XN8 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | 85mA Dual H-Bridge Odometer Driver with Divide by Select |
| 中文描述： | 85毫安雙H橋里程表與除以選擇驅動程序 |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 149K |
| 代理商： | CS8441XN8 |
3
Figure 2: Divide by 1 SELECT Mode
C
SENSOR is a PNP comparator input which accepts a sine wave
input or a square wave input. This input is protected from excur-
sions above V
CC
as well as any below ground, as long as the cur-
rent is limited to 1.5mA. It has an active clamp set to zero volts to
prevent negative input voltages from disrupting normal opera-
tion. The sensor input can withstand 150V
DC
as long as the input
current is limited to 1.5mA max using a series resistor of 100k.
Simultaneously energizing the source and sink on either leg is
not permitted. i.e. Q1 & Q2 or Q3 & Q4 cannot be energized
simultaneously.
Circuit function is not affected by inductive transients due to coil
loads as specified in Transition States section.
The transition states occur as indicated in Table 1 without any
intermediate states permitted.
Table 1: Transition States
The polarity definition for the coil driver outputs is as follows:
Connect
Polarity
Coil +
Positive (+)
V
CC
Negative (-)
Gnd
Connect
Coil -
Gnd
V
CC
The speed sensor input frequency is divided by one or divided
by two by connecting the divider select input, (Pin 5) as follows:
Logic 0 = divide by 2
Logic 1 = divide by 1
Circuit Operation
Speed Sensor Input
Coil Driver Outputs
Divider Select Input
Short
Circuit
V
CC
Sense
Resistor
Coil
Short
Circuit
Sense
Resistor
Gnd
Q3
Q4
Q1
Q2
Overvoltage
and
Short
Circuit
Protection
Package Pin Description
PACKAGE PIN #
PIN SYMBOL
FUNCTION
Figure 1: Coil Driver Output
Figure 3: Divide by 2 SELECT Mode
Output State Table
Coil A
+
OFF
-
-
-
OFF
+
+
State
0
1
2
3
4
5
6
7
Coil B
+
+
+
OFF
-
-
-
OFF
DIVIDE BY ONE MODE SELECT = V
CC
DIVIDE BY TWO MODE SELECT = Gnd
8L PDIP
1
Gnd
Ground connection.
2
COILA+
Output stage, when active, this pin supplies current to COIL A.
3
COILA-
Output stage, when active, this pin supplies current to COIL A.
4
SENSOR
Input signal from wheel speed or engine rpm.
5
SELECT
Selects divide by 1 or divide by 2 mode.
6
COILB-
Output stage, when active, this pin supplies current to COIL B.
7
COILB+
Output stage, when active, this pin supplies current to COIL B.
8
V
CC
Supply Voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| CSD01060A | Zero Recovery㈢ Rectifiers |
| CSD01060E | Zero Recovery㈢ Rectifiers |
| CSD02060A | Zero Recovery㈢ Rectifiers |
| CSD02060G | Zero Recovery㈢ Rectifiers |
| CSD04060A | Zero Recovery㈢ Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS8441YN8 | 功能描述:IC DRIVER STEPPER MOTOR 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| CS8442 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:85mA Dual H-Bridge Odometer Driver with Buffered Speed Signal Output |
| CS8442/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Stepper Motor Driverwith Buffered Speed Signal Output |
| CS-8442N8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Stepper Motor Controller/Driver |
| CS8442XN8 | 制造商:CHERRY 制造商全稱:CHERRY 功能描述:85mA Dual H-Bridge Odometer Driver with Buffered Speed Signal Output |
發布緊急采購，3分鐘左右您將得到回復。