- 您現在的位置：買賣IC網 > PDF目錄352822 > CS5156HGD16 Analog IC PDF資料下載
參數資料
| 型號： | CS5156HGD16 |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 197K |
| 代理商： | CS5156HGD16 |
CS5151H
http://onsemi.com
9
Figure 8. Peak–to–Peak Ripple on VOUT = 2.8 V,
IOUT = 13 A (Heavy Load)
M 1.00
s
Trace 1– Regulator Output Voltage (10 V/div.)
Trace 2– Inductor Switching Node (5.0 V/div.)
Transient Response
The CS5151H V2 control loop’s 100 ns reaction time
provides unprecedented transient response to changes in
input voltage or output current. Pulse by pulse adjustment of
duty cycle is provided to quickly ramp the inductor current
to the required level. Since the inductor current cannot be
changed instantaneously, regulation is maintained by the
output capacitor(s) during the time required to slew the
inductor current.
Overall load transient response is further improved
through a feature called “adaptive voltage positioning”. This
technique pre–positions the output capacitor’s voltage to
reduce total output voltage excursions during changes in
load.
Holding tolerance to 1.0% allows the error amplifier’s
reference voltage to be targeted +40 mV high without
compromising
DC
accuracy.
A
“droop
resistor”,
implemented through a PC board trace, connects the error
amplifier’s feedback pin (VFB) to the output capacitors and
load and carries the output current. With no load, there is no
DC drop across this resistor, producing an output voltage
tracking the error amplifier’s, including the +40 mV offset.
When the full load current is delivered, an 80 mV drop is
developed across this resistor. This results in output voltage
being offset –40 mV low.
The result of adaptive voltage positioning is that
additional margin is provided for a load transient before
reaching the output voltage specification limits. When load
current suddenly increases from its minimum level, the
output capacitor is pre–positioned +40 mV. Conversely,
when load current suddenly decreases from its maximum
level, the output capacitor is pre–positioned –40 mV (see
Figures 9, 10, and 11). For best transient response, a
combination of a number of high frequency and bulk output
capacitors are usually used.
If the maximum on time is exceeded while responding to
a sudden increase in load current, a normal off time occurs
to prevent saturation of the output inductor.
Figure 9. CS5151H Demonstration Board Response
to a 0.5 to 13 A Load Pulse (Output Set for 2.8 V)
Trace 2– Regulator Output Voltage (20 V/div.)
Trace 1– Regulator Output Voltage (1.0 V/div.)
Figure 10. CS5151H Demonstration Board Response to
13 A Load Turn On (Output Set for 2.8 V). Upon
Completing a Normal Off Time, The V2 Control Loop
Immediately Connects the Inductor to the Input
Voltage, Providing 100% Duty Cycle. Regulation is
Achieved in Less Than 20
ms
Trace 1– Regulator Output Voltage (1.0 V/div.)
Trace 2– Inductor Switching Node (5.0 V/div.)
Trace 3– Output Current (0.5 to 13 Amps) (20 V/div.)
相關PDF資料 |
PDF描述 |
|---|---|
| CS5156HGDR16 | Analog IC |
| CS-5156N16 | Voltage-Mode SMPS Controller |
| CS-5157D16 | Voltage-Mode SMPS Controller |
| CS-5157HD16 | Voltage-Mode SMPS Controller |
| CS-5157HDR16 | Voltage-Mode SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS-5156N16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| CS-5157D16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| CS-5157HD16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| CS-5157HDR16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| CS5157HGD16 | 功能描述:DC/DC 開關控制器 5-Bit Synchronous RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。