- 您現在的位置：買賣IC網 > PDF目錄42912 > CPC7695BATR (CLARE INC) PDF資料下載
參數資料
| 型號： | CPC7695BATR |
| 廠商： | CLARE INC |
| 元件分類： | 通信及網絡 |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO28 |
| 封裝： | SOIC-28 |
| 文件頁數： | 10/23頁 |
| 文件大?。?/td> | 677K |
| 代理商： | CPC7695BATR |
CPC7695
18
PRELIMINARY
R00D
switches when pulled to a logic low. Although logically
disabled, an active (closed) ringing switch (SW4) will
remain closed until the next current zero crossing
event.
As shown in the table “Break-Before-Make Operation
operation is similar to the one shown in “Alternate
Transition)” on page 18, except in the method used to
select the all-off state and when the INRINGING,
INTESTin and INTESTout inputs are reconfigured for the
talk state.
1.
Pull TSD to a logic low to end the ringing state.
This opens the ringing return switch (SW3) and
prevents any other switches from closing.
2.
Keep TSD low for at least one-half the duration of
the ringing cycle period to allow sufficient time for
a zero crossing current event to occur and for the
circuit to enter the break before make state.
3.
During the TSD low period, set the INRINGING,
INTESTin and INTESTout inputs to the talk state
(0,0,0).
4.
Release TSD allowing the internal pull-up to
activate the break switches.
When using TSD as an input, the two recommended
states are “0” which over rides logic input pins and
forces an all-off state and “Z” which allows switch
control via the logic input pins. This requires the use of
an open-collector or open-drain type buffer.
Alternate Break-Before-Make Operation Logic Table (Ringing to Talk Transition)
2.4 Data Latch
The CPC7695 has an integrated transparent data
latch. The latch enable operation is controlled by TTL
logic input levels at the LATCH pin. Data input to the
latch are via the input pins, while the output of the data
latch are internal nodes used for state control. When
the LATCH enable control pin is at logic 0 the data
latch is transparent and the input data control signals
flow directly through the latch to the state control
circuitry. A change in input will be reflected by a
change in switch state. Whenever the LATCH enable
control pin is at logic 1, the latch is active and data is
locked. Subsequent input changes will not result in a
change to the control logic or affect the existing switch
state.
Switches will remain in the state they were in when the
LATCH pin changes from logic 0 to logic 1 and will not
respond to changes in input as long as the latch is at
logic 1. However, neither the TSD input nor the TSD
output control functions are affected by the latch
function. Internal thermal shutdown control and
external “All-off” control via TSD is not affected by the
state of the LATCH enable input.
2.5 TSD Pin Description
The TSD pin is a bi-directional I/O structure with an
internal pull up sourced from VDD. As an output, this
pin indicates the status of the thermal shutdown
circuitry. Typically, during normal operation, this pin will
be pulled up to VDD but under fault conditions that
create excess thermal loading the CPC7695 will enter
thermal shutdown and a logic low will be output.
State
INRINGING INTESTin INTESTout
Latch
TSD
Timing
Break
Switches
Ringing
Return
Switch
(SW3)
Ringing
Switch
(SW4)
Test
Switches
Ringing
1
0
Z
-
Off
On
Off
All-off
1
0
1
X0
Hold this state for at least
one-half of ringing cycle.
SW4 waiting for zero current
to turn off.
Off
On
Off
Break-
Before-
Make
00
0
Zero current has occurred.
SW4 has opened
Off
Talk
0
Z
Break switches close.
On
Off
* For the CPC7695xA/B versions the input pattern (1,1,1) may also be used for the all-off state.
相關PDF資料 |
PDF描述 |
|---|---|
| CPC7695BBTR | |
| CPC7695BCTR | |
| CQY36N | LED IrLED 950nm 2-Pin T-3/4 Bulk |
| CQY37N | LED IrLED 950nm 2-Pin T-3/4 Bulk |
| CSTCR4M00G55A-R0 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPC7695BB | 功能描述:固態繼電器-PCB安裝 TTL LCAS10, DMOS SW8 w Protection SCR, TTL Inputs, High SW4 DV/DT RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC7695BBTR | 功能描述:固態繼電器-PCB安裝 TTL LCAS10, DMOS SW8 w Protection SCR, TTL Inputs, High SW4 DV/DT, TAPE/REEL RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC7695BC | 功能描述:固態繼電器-PCB安裝 TTL LCAS10, DMOS SW8 w Protection SCR & Extra Logic, TTL Inputs, High SW4 DV/DT RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC7695BCTR | 功能描述:固態繼電器-PCB安裝 TTL LCAS10, DMOS SW8 w Protection SCR & Extra Logic, TTL Inputs, High SW4 DV/DT, TAPE/REEL RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC7695ZA | 功能描述:IC LINE CARD ACCESS SW 20-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
發布緊急采購，3分鐘左右您將得到回復。