- 您現(xiàn)在的位置：買賣IC網 > PDF目錄379952 > COP8SGB040N9 (National Semiconductor Corporation) LMK01000 / LMK01010 / LMK01020 1.6 GHz High Performance Clock Buffer, Divider, and Distributor; Package: LLP; No of Pins: 48 PDF資料下載
參數資料
| 型號： | COP8SGB040N9 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | LMK01000 / LMK01010 / LMK01020 1.6 GHz High Performance Clock Buffer, Divider, and Distributor; Package: LLP; No of Pins: 48 |
| 中文描述： | 8位的CMOS基于ROM和OTP微控制器具有8K到32K的內存，2個比較器和USART |
| 文件頁數： | 23/62頁 |
| 文件大?。?/td> | 913K |
| 代理商： | COP8SGB040N9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
6.0 Timers
(Continued)
In this mode the input pin TxB can be used as an indepen-
dent positive edge sensitive interrupt input if the TxENB
control flag is set. The occurrence of a positive edge on the
TxB input pin is latched into the TxPNDB flag.
Figure 16 shows a block diagram of the timer in External
Event Counter mode.
Note:
The PWM output is not available in this mode since the TxApin is being
used as the counter input clock.
6.2.3 Mode 3. Input Capture Mode
Each device can precisely measure external frequencies or
time external events by placing the timer block, Tx, in the
input capture mode. In this mode, the reload registers serve
as independent capture registers, capturing the contents of
the timer when an external event occurs (transition on the
timer input pin). The capture registers can be read while
maintaining count, a feature that lets the user measure
elapsed time and time between events. By saving the timer
value when the external event occurs, the time of the exter-
nal event is recorded. Most microcontrollers have a latency
time because they cannot determine the timer value when
the external event occurs. The capture register eliminates
the latency time, thereby allowing the applications program
to retrieve the timer value stored in the capture register.
In this mode, the timer Tx is constantly running at the fixed t
C
rate. The two registers, RxA and RxB, act as capture regis-
ters. Each register acts in conjunction with a pin. The register
RxAacts in conjunction with the TxApin and the register RxB
acts in conjunction with the TxB pin.
The timer value gets copied over into the register when a
trigger event occurs on its corresponding pin. Control bits,
TxC3, TxC2 and TxC1, allow the trigger events to be speci-
fied either as a positive or a negative edge. The trigger
condition for each input pin can be specified independently.
The trigger conditions can also be programmed to generate
interrupts. The occurrence of the specified trigger condition
on the TxA and TxB pins will be respectively latched into the
pending flags, TxPNDA and TxPNDB. The control flag Tx-
ENA allows the interrupt on TxA to be either enabled or
disabled. Setting the TxENA flag enables interrupts to be
generated when the selected trigger condition occurs on the
TxA pin. Similarly, the flag TxENB controls the interrupts
from the TxB pin.
Underflows from the timer can also be programmed to gen-
erate interrupts. Underflows are latched into the timer TxC0
pending flag (the TxC0 control bit serves as the timer under-
flow interrupt pending flag in the Input Capture mode). Con-
sequently, the TxC0 control bit should be reset when enter-
ing the Input Capture mode. The timer underflow interrupt is
enabled with the TxENA control flag. When a TxA interrupt
occurs in the Input Capture mode, the user must check both
the TxPNDA and TxC0 pending flags in order to determine
whether a TxA input capture or a timer underflow (or both)
caused the interrupt.
Figure 17 shows a block diagram of the timer T1 in Input
Capture mode. Timer T2 and T3 are identical to T1.
10131746
FIGURE 15. Timer in PWM Mode
10131747
FIGURE 16. Timer in External Event Counter Mode
10131748
FIGURE 17. Timer in Input Capture Mode
C
www.national.com
23
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SGB040Q3 | LMK01000 / LMK01010 / LMK01020 1.6 GHz High Performance Clock Buffer, Divider, and Distributor; Package: LLP; No of Pins: 48 |
| COP8SGB040Q6 | LMK01000 / LMK01010 / LMK01020 1.6 GHz High Performance Clock Buffer, Divider, and Distributor; Package: LLP; No of Pins: 48 |
| COP8SGB040Q7 | 8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
| COP8SGB040Q8 | 8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
| COP8SGB040Q9 | 8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SGB040Q3 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
| COP8SGB040Q6 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
| COP8SGB040Q7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
| COP8SGB040Q8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
| COP8SGB040Q9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and USART |
發(fā)布緊急采購，3分鐘左右您將得到回復。