- 您現在的位置：買賣IC網 > PDF目錄3791 > COP8CBR9KMT8 (National Semiconductor)IC MCU EEPROM 8BIT 32K 56-TSSOP PDF資料下載
參數資料
| 型號： | COP8CBR9KMT8 |
| 廠商： | National Semiconductor |
| 文件頁數： | 34/111頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU EEPROM 8BIT 32K 56-TSSOP |
| 標準包裝： | 34 |
| 系列： | COP8™ 8C |
| 核心處理器： | COP8 |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 連通性： | Microwire/Plus（SPI），UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 49 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-TFSOP（0.240"，6.10mm 寬） |
| 包裝： | 管件 |
| 其它名稱： | *COP8CBR9KMT8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
Case 2 shows a subsequent dip in the supply voltage which goes below the approximate 1.8V level. As
VCC drops below Vbor, the internal RESET signal is asserted. When VCC rises back above the 1.8V level, td
is started. Since the power supply rise time is longer for this case, td has expired before VCC
Vbor and tid starts immediately when VCC is greater than Vbor.
Case 3 shows a dip in the supply where VCC drops below Vbor, but not below 1.8V. On-chip RESET is
asserted when VCC goes below Vbor and tid starts as soon as the supply goes back above Vbor.
If the Brownout Reset feature is enabled, the internal reset will not be turned off until the Idle Timer
underflows. The internal reset will perform the same functions as external reset. The device is ensured to
operate at the specified frequency down to the specified brownout voltage. After the underflow, the logic is
designed such that no additional internal resets occur as long as VCC remains above the brownout
voltage.
The device is relatively immune to short duration negative-going VCC transients (glitches). It is essential
that good filtering of VCC be done to ensure that the brownout feature works correctly. Power supply
decoupling is vital even in battery powered systems.
There are two optional brownout voltages. The part numbers for the three versions of this device are:
COP8CBR, Vbor = low voltage range
COP8CCR, Vbor = high voltage range
COP8CDR, BOR is disabled.
Refer to the device specifications for the actual Vbor voltages.
High brownout voltage devices are ensured to operate at 10MHz down to the brownout voltage. Low
brownout voltage devices are ensured to operate at 3.33MHz down to the brownout voltage. Devices are
not ensured to operate at 10MHz down to the low brownout voltage.
Under no circumstances should the RESET pin be allowed to float. If the on-chip Brownout Reset feature
is being used, the RESET pin should be connected directly to VCC. The RESET input may also be
connected to an external pull-up resistor or to other external circuitry. Any rising edge on the RESET pin
while VCC is below the specified operating range may cause unpredictable results. The output of the
brownout reset detector will always preset the Idle Timer to a value between 00F0 and 00FF (240 to 256
tC). At this time, the internal reset will be generated.
If the BOR feature is disabled, then no internal resets are generated and the Idle Timer will power-up with
an unknown value. In this case, the external RESET must be used. When BOR is disabled, this on-chip
circuitry is disabled and draws no DC current.
The contents of data registers and RAM are unknown following the on-chip reset.
Figure 5-5. Reset Circuit Using Power-On Reset
5.8
OSCILLATOR CIRCUITS
The device has two crystal oscillators to facilitate low power operation while maintaining throughput when
required. Further information on the use of the two oscillators is found in Power Saving Features. The low
speed oscillator utilizes the L0 and L1 port pins. References in the following text to CKI will also apply to
L0 and references to G7/CKO will also apply to L1.
Copyright 2000–2013, Texas Instruments Incorporated
Functional Description
29
相關PDF資料 |
PDF描述 |
|---|---|
| COP8CBR9HLQ8 | IC MCU CMOS 8BIT 44LLP |
| MC9S08SH32VTJ | MCU 8BIT 32K FLASH 20-TSSOP |
| MC9S08SH32VTG | MCU 8BIT 32K FLASH 16-TSSOP |
| MC9S08SH16VWL | MCU 8BIT 16K FLASH 28-SOIC |
| MC9S08SH16VTL | MCU 8BIT 16K FLASH 28-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8CBR9LVA8 | 功能描述:IC MCU EEPROM 8BIT 32K 68PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8C 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| COP8CCE9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset |
| COP8CCE9HLQ7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset |
| COP8CCE9HLQ9 | 功能描述:IC MCU FLASH 8BIT 8K A/D 44LLP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8C 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| COP8CCE9HVA7 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。