- 您現在的位置：買賣IC網 > PDF目錄379928 > COP313CH (National Semiconductor Corporation) Single-Chip CMOS Microcontrollers PDF資料下載
參數資料
| 型號： | COP313CH |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Single-Chip CMOS Microcontrollers |
| 中文描述： | 單芯片的CMOS微控制器 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 223K |
| 代理商： | COP313CH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Functional Description
(Continued)
The SIO register functions as a 4-bit serial-in/serial-out shift
register or as a binary counter, depending upon the con-
tents of the EN register. (See EN register description be-
low.) Its contents can be exchanged with A, allowing
it to input or output a continuous serial data stream. With
SIO functioning as a serial-in/serial-out shift register and SK
as a sync clock, the COP413C is MICROWIRE compatible.
The XAS instruction copies C into the SKL latch. In the
counter mode, SK is the output of SKL; in the shift register
mode, SK is a sync clock, inhibited when SKL is a logic ‘‘0’’.
The EN register is an internal 4-bit register loaded under
program control by the LEI instruction. The state of each bit
of this register selects or deselects the particular feature
associated with each bit of the EN register (EN3–EN0).
1. The least significant bit of the enable register, EN0, se-
lects the SIO register as either a 4-bit shift register or as a
4-bit binary counter. With EN0 set, SIO is an asynchro-
nous binary counter, decrementing its value by one upon
each low-going pulse (‘‘1’’ to ‘‘0’’) occurring on the SI
input. Each pulse must be at least two instruction cycles
wide. SK outputs the value of SKL. The SO output is
equal to the value of EN3. With EN0 reset, SIO is a serial
shift register, shifting left each instruction cycle time. The
data present at SI is shifted into the least significant bit of
SIO. SO can be enabled to output the most significant bit
of SIO each instruction cycle time. (See 4, below.) The
SK output becomes a logic-controlled clock.
2. EN 1 is not used, it has no effect on the COP413C.
3. With EN2 set, the L drivers are enabled to output the data
in Q to the L I/O ports. Resetting EN2 disables the L
drivers, placing the L I/O ports in a high impedance input
state.
4. EN3, in conjunction with EN0, affects the SO output. With
EN0 set (binary counter option selected), SO will output
the value loaded into EN3. With EN0 reset (serial shift
register option selected), setting EN3 enables SO as the
output of the SIO shift register, outputting serial shifted
data each instruction time. Resetting EN3 with the serial
shift register option selected, disables SO as the shift
register output; data continues to be shifted through SIO
and can be exchanged with A via an XAS instruction but
SO remains reset to ‘‘0’’.
INITIALIZATION
The external RC network shown in Figure 5 must be con-
nected to the RESET pin. The RESET pin is configured as a
Schmitt trigger input. If not used, it should be connected to
V
CC
. Initialization will occur whenever a logic ‘‘0’’ is applied
to the RESET input, providing it stays low for at least three
instruction cycle times.
Upon initialization, the PC register is cleared to 0 (ROM ad-
dress 0) and the A, B, C, EN, and G registers are cleared.
The SK output is enabled as a SYNC output, providing a
pulse each instruction cycle time. Data memory (RAM) is
not cleared upon initialization. The first instruction at ad-
dress 0 must be a CLRA (clear A register).
TL/DD/8537–5
RC
l
5
c
Power Supply Rise Time
and RC
l
100
c
CKI Period
FIGURE 5. Power-Up Clear Circuit
TABLE I. Enable Register ModesDBits EN0 and EN3
EN0
EN3
SIO
SI
SO
SK
0
0
Shift Register
Input to Shift
Register
Input to Shift
Register
Input to Counter
Input to Counter
0
If SKL
e
1, SK
e
clock
If SKL
e
0, SK
e
0
If SKL
e
1, SK
e
clock
If SKL
e
0, SK
e
0
SK
e
SKL
SK
e
SKL
0
1
Shift Register
Serial
out
0
1
1
1
0
1
Binary Counter
Binary Counter
8
相關PDF資料 |
PDF描述 |
|---|---|
| COP413C | Single-Chip CMOS Microcontrollers |
| COP470 | COP470 V.F Display Driver |
| COP472-3 | COP472-3 Liquid Crystal Display Controller |
| COP472MW-3 | COP472-3 Liquid Crystal Display Controller |
| COP472N-3 | COP472-3 Liquid Crystal Display Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP313CH-XXX/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| COP313CH-XXX/N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| COP313C-XXX/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| COP313C-XXX/N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| COP313C-XXX/WM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。