參數資料
型號： CM312
廠商： Electronic Theatre Controls, Inc.
英文描述： Communications utilityModule
中文描述： 通訊utilityModule
文件頁數： 36/56頁
文件大?。?/td> 175K
代理商： CM312
CM312 Quad Serial utilityModule
26
RTD Embedded Technologies, Inc.
Chapter 4
U
SING THE UTILITY
M
ODULE
E
THERNET
P
ORTS
Using the utilityModule is straightforward, and essentially identical to any other Ethernet card.
When CM312 module is powered on, data in the EEPROM on board is transferred to Ethernet
controller’s internal configuration registers. The data in the EEPROM contains information
configuration such as the base address of the card, the active interrupt line on the PC/104 bus for
Ethernet access, the media type in use, etc. The factory default setting of the board is at I/O
address 0x320 and IRQ 5. And if there is a resource conflicting, you need to change your setting
on CM312 with the other I/O boards removed temporally by executing CM312SET program as
described in the later chapter.
The following sections describe:
Diagnostic LEDs
Boot ROM socket
Power Consumption
Diagnostic LEDs
If CN8, the RJ45 connector, has two LEDs that are used to indicate status and provide some
diagnostic information in case of malfunctions.
Name
COL
LNK
Meaning
Collision Detected
Link established (UTP)
Normal State
Off
On (10Base-T only)
COL LED
The LED is normally off, and flashes when the module detects a collision on the network.
Collisions may be due to low-quality cable, which allows crosstalk between the transmit and
receive pairs, miswiring, or a malfunctioning device on the network.
LNK LED
The LED is turned on when a valid 10Base-T link is detected by the chipset. It is only active when
using the 10Base-T UTP connection with link integrity checking enabled. If it is off, the UTP
wiring may be broken or incorrect, link integrity checking may be disabled, or you may be using
the 10Base-2 or AUI interface.
Boot ROM Socket
In some applications, you may wish to use the boot ROM socket of the utilityModule to boot a
connected cpuModule from a remote server.
The socket will accomodate a 32 pin PLCC EPROM or Flash memory devices of size 8k, 16k,
32k, or 64k bytes. The device must be a byte-wide architecture.
The boot ROM feature can be enabled using the CM312SET program described on page 28.
相關PDF資料
PDF描述
CM6503 8-PIN SINGLE PFC CONTROLLER WITH 50% PWM CLOCK SIGNAL
CM6503IP 8-PIN SINGLE PFC CONTROLLER WITH 50% PWM CLOCK SIGNAL
CM6504IP 8-PIN SINGLE PFC CONTROLLER WITH 50% PWM CLOCK SIGNAL
CM6504 8-PIN SINGLE PFC CONTROLLER WITH 50% PWM CLOCK SIGNAL
CM6824 LOW START-UP CURRENT PFC/PWM CONTROLLER COMBO
相關代理商/技術參數
參數描述
CM3121 制造商:CALMIRCO 制造商全稱:California Micro Devices Corp 功能描述:Dual Linear Voltage Regulator for DDR-I and DDR-II Memory
CM312102SB 制造商:CALMIRCO 制造商全稱:California Micro Devices Corp 功能描述:Dual Linear Voltage Regulator for DDR-I and DDR-II Memory
CM3121-02SB 制造商:CALMIRCO 制造商全稱:California Micro Devices Corp 功能描述:Dual Linear Voltage Regulator for DDR-I and DDR-II Memory
CM3121-02SH 制造商:CALMIRCO 制造商全稱:California Micro Devices Corp 功能描述:Dual Linear Voltage Regulator for DDR-I and DDR-II Memory
CM313 功能描述:LED T3-1/4 MINI BAYONET RoHS:是 類別:光電元件 >> LED - 燈更換 系列:* 標準包裝:100 系列:- 可更換燈:- 尺寸/尺寸:T - 1 3/4 波長:- 正向電壓:28V 底座類型:小型帽沿 顏色:黃 Millicandela 等級:22mcd 配置:單一 應用:白熾燈替換件，指示燈 其它名稱:925.0112925.0112-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*