參數資料
型號: CM2596GSJCN220
廠商: Electronic Theatre Controls, Inc.
英文描述: 3A STEP DOWN VOLTAGE REGULATOR
中文描述: 第3A降壓穩壓器
文件頁數: 10/12頁
文件大?。?/td> 482K
代理商: CM2596GSJCN220
CM2596
3A S
TEP
D
OWN
V
OLTAGE
R
EGULATOR
Feedback Connection
For fixed output voltage version, the FB (feedback) pin must be connected to V
OUT
. For the adjustable version, it is important to
place the output voltage ratio resistors near CM2596 as possible in order to minimize the noise introduction.
Enable
It is required that the
ENABLE
must not be left open. For normal operation, connect this pin to a “LOW” voltage (typically, below
1.6V). On the other hand, for standby mode, connect this pin with a “HIGH” voltage. This pin can be safely pulled up to +V
IN
without a resistor in series with it.
Grounding
To maintain output voltage stability, the power ground connections must be low-impedance. For the 5-lead TO-220 and TO-263
style package, both the tab and pin 3 are ground and either connection may be used.
Heatsink and Thermal Consideration
Although the CM2596 requires only a small heatsink for most cases, the following thermal consideration is important for all
operation. With the package thermal resistances
θ
JA and
θ
JC, total power dissipation can be estimated as follows:
P
D
= (V
IN
x I
Q
) + (V
OUT
/ V
IN
)(I
LOAD
x V
SAT
);
When no heatsink is used, the junction temperature rise can be determined by the following:
T
J
= P
D
x
θ
JA
;
With the ambient temerpature, the actual junction temperature will be:
T
J
=
T
J
+ T
A
;
If the actual operating junction temperature is out of the safe operating junction temperature (typically 125
), then a heatsink is
required. When using a heatsink, the junction temperature rise will be reduced by the following:
T
J
= P
D
x (
θ
JC
+
θ
interface
+
θ
Heatsink
);
Also one can see from the above, it is important to choose an heatsink with adequate size and thermal resistance, such that to
maintain the regulator’s junction temperature below the maximum operating temperature.
Layout guideline
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance can generate
voltage transients which can cause problems. For minimal inductance and ground loops, the wires indicated by
heavy lines
should be wide printed circuit traces and should be kept as short as possible.
For best results, external components should
be located as close to the switcher lC as possible using ground plane construction or single point grounding.
If
open core inductors are used,
special care must be taken as to the location and positioning of this type of inductor. Allowing
the inductor flux to intersect sensitive feedback, lC ground path and COUT wiring can cause problems.
When using the adjustable version, special care must be taken as to the location of the feedback resistors and the associated
wiring. Physically locate both resistors near the IC, and route the wiring away from the inductor, especially an open core type of
inductor. (See application section for more information.)
2005/03/04 Champion Microelectronic Corporation
Page 10
相關PDF資料
PDF描述
CM2596GSJCN263 3A STEP DOWN VOLTAGE REGULATOR
CM2596SJCN220 3A STEP DOWN VOLTAGE REGULATOR
CM2596SJCN263 3A STEP DOWN VOLTAGE REGULATOR
CM2596ZJCN220 3A STEP DOWN VOLTAGE REGULATOR
CM2596ZJCN263 Pleated Foil Shielded Cable; Number of Conductors:25; Pitch Spacing:0.05"; Conductor Size AWG:28; No. Strands x Strand Size:7 x 36; Jacket Material:Polyvinylchloride (PVC); Conductor Material:Copper; Conductor Plating:Tin RoHS Compliant: Yes
相關代理商/技術參數
參數描述
CM2596GSJCN263 制造商:未知廠家 制造商全稱:未知廠家 功能描述:3A STEP DOWN VOLTAGE REGULATOR
CM2596S 制造商:CHAMP 制造商全稱:CHAMP 功能描述:3A STEP DOWN VOLTAGE REGULATOR
CM2596S_06 制造商:CHAMP 制造商全稱:CHAMP 功能描述:3A STEP DOWN VOLTAGE REGULATOR
CM2596SCN220 制造商:CHAMP 制造商全稱:CHAMP 功能描述:3A STEP DOWN VOLTAGE REGULATOR
CM2596SCN263 制造商:CHAMP 制造商全稱:CHAMP 功能描述:3A STEP DOWN VOLTAGE REGULATOR