- 您現在的位置：買賣IC網 > PDF目錄237309 > CK2660-7RD4 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CK2660-7RD4 |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | HEAT SINK, METAL, CASE K02, MODULE |
| 文件頁數： | 4/31頁 |
| 文件大?。?/td> | 637K |
| 代理商： | CK2660-7RD4 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
12/31
Output Protection
Each output is protected against overvoltages which could
occur due to a failure of the internal control circuit. Voltage
suppressor diodes (which under worst case condition may
become a short circuit) provide the required protection. The
suppressor diodes are not designed to withstand externally
applied overvoltages. Overload at any of the outputs will
cause a shut-down of all outputs. A red LED indicates the
overload condition.
Parallel or Series Connection of Units
Single or double output units with equal nominal output
voltage can be connected in parallel without any precau-
tions using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71°C (e.g. 85°C) if TC max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Typical dynamic load regulation of Uo1 and Uo2
相關PDF資料 |
PDF描述 |
|---|---|
| CK2660-9ERD0 | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| CK2660-9ERD3 | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| CD-700-KAC-HHB-13.000 | PHASE LOCKED LOOP, CQCC16 |
| CD-700-KAF-GBB-13.000 | PHASE LOCKED LOOP, CQCC16 |
| CD-700-KAF-GKB-20.000 | PHASE LOCKED LOOP, CQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CK2660-9ER | 制造商:Power-One 功能描述:DCDC - Bulk |
| CK2660-9ERG | 功能描述:POWER SUPPLYDC-DC CONVERTERIND-R 制造商:bel power solutions 系列:Melcher K 零件狀態:在售 類型:封閉式，保形涂層 電壓 - 輸入（最小值）:28V 電壓 - 輸入（最大值）:140V 輸出數:2 電壓 - 輸出 1:24V 電壓 - 輸出 2:24V 電壓 - 輸出 3:- 電壓 - 輸出 4:- 電流 - 輸出（最大值）:3A，3A 功率（W）:144W 應用:ITE（商業），鐵路 工作溫度:-40°C ~ 71°C 效率:84% 安裝類型:底座安裝 大小/尺寸:6.73" 長 x 4.37" 寬 x 3.15" 高（171.0mm x 111.0mm x 80.0mm） 認可:cCSAus，CE，NEMKO 標準包裝:5 |
| CK2660-9ERT | 功能描述:DC/DC CONVERTER 制造商:bel power solutions 系列:* 零件狀態:有效 標準包裝:5 |
| CK-27 | 制造商:Sunhayato 功能描述: |
| CK2705 6.35X17.5MM FLAT SHAFT | 功能描述:旋鈕開關 RTRY 4POL 3POS SOLDR 6.35X17.5MM FLT SHFT RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
發布緊急采購，3分鐘左右您將得到回復。