參數資料
型號： CH7003B-V
廠商： Electronic Theatre Controls, Inc.
英文描述： Digital PC to TV Encoder
中文描述： 數碼電腦電視編碼器
文件頁數： 37/50頁
文件大小： 334K
代理商： CH7003B-V
CHRONTEL
CH7003B
201-0000-023 Rev 4.1, 8/2/99
37
Register Descriptions
(continued)
Vertical Postiion Register
Symbol: VPR
Address: 0BH
Bits: 8
This register is used to shift the displayed TV image in a vertical direction (up or down) to achieve a vertically cen-
tered image on screen. This bit field, VP[8:0] represents the TV line number (relative to the VGA vertical sync)
used to initiate the generation and insertion of the TV vertical interval (i.e., the first sequence of equalizing pulses).
Increasing values delay the output of the TV vertical sync, causing the image position to move UP on the TV screen.
Decreasing values, therefore, move the image position DOWN. Each increment moves the image position by one
TV line (approximately 2 VGA lines). The maximum value that should be programmed into the VP[8:0] value is
the number of TV lines minus 1, divided by 2 (262, 312 or 313). When panning the image up, the number should be
increased until (TVLPF-1) / 2 is reached; the next step should be to reset the value to zero. When panning the image
down the screen, the VP[8:0] value should be decremented until the value zero is reached. The next step should set
the value to (TVLPF-1) / 2, and then decrementing can continue. If this value is programmed to a number greater
than (TV lines per frame-1) /2, a TV vertical SYNC will not be generated.
Sync Polarity Register
Symbol: SPR
Address: 0DH
Bits: 4
This register provides selection of the synchronization signal input to, or output from, the CH7003.
HSP (bit 0) is Horizontal Sync Polarity - an HSP value of zero means the horizontal sync is active low, and a
value of one means the horizontal sync is active high.
VSP (bit 1) is Vertical Sync Polarity - a VSP value of zero means the vertical sync is active low, and a value
of one means the vertical sync is active high.
SYO (bit 2) is Sync Direction - a SYO value of zero means that H and V sync are input to the CH7003. A
value of one means that H and V sync are output from the CH7003.
DES (bit 3) is Detect Embedded Sync - a DES value of zero means that H and V sync will be obtained from
the direct pin inputs. A DES value of one means that H and V sync will be detected from the embedded codes
on the pixel input stream. Note that this will only be valid for the YCrCb input modes.
Note:
When sync direction is set to be an output, horizontal sync will use a fixed pulse width of 64 pixels and vertical
sync will use a fixed pulse width of 2 lines.
Bit:
Symbol:
7
VP7
6
VP6
5
VP5
4
VP4
3
VP3
2
VP2
1
VP1
0
VP0
Type:
Default:
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Bit:
Symbol:
7
6
5
4
3
DES
2
SYO
1
VSP
0
HSP
Type:
Default:
R/W
R/W
R/W
R/W
0
0
0
0
相關PDF資料
PDF描述
CH7006C MODULE
CH7006C-T Circular Connector; Body Material:Aluminum; Series:PT06; Number of Contacts:18; Connector Shell Size:14; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:14-18
CH7006C-V Circular Connector; Body Material:Aluminum; Series:PT06; No. of Contacts:18; Connector Shell Size:14; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:14-18
CH7013A Digital PC to TV Encoder
CH7013A-T Digital PC to TV Encoder
相關代理商/技術參數
參數描述
CH7004C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision
CH7004C-T 制造商:CHRONTEL 功能描述:
CH7004C-V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision
CH7005C-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision
CH7005C-V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*