參數資料
型號： CH2056ETBR
廠商： Electronic Theatre Controls, Inc.
英文描述： HIGH SPEED Modem and FAX FAMILY
中文描述： 高速調制解調器和傳真家庭
文件頁數： 7/19頁
文件大?。?/td> 365K
代理商： CH2056ETBR
Cermetek Microelectronics, Inc.
code 0) or the command is valid or accepted, or with
an ERROR (result code 4) if the command is not
recognized. The detail contained in the error result
codes signaled to the DTE depends on the level of
message suppression employed by the user. As can
be seen from Tables 5A, 5B and 5C, specifying X4
allows the HS Modem to utilize the entire range of
non-extended messages, whereas X0 suppresses all
but the very basic result codes. Most of the result
codes allowed under X1, X2 and X3 are considered
call progress status codes and, in practice, are
suppressed except for the case of debugging
activities. It is recommended that the non-extended
result codes be used in all cases.
It should be noted that the default connect result codes
9-20 indicate DTE connection speed, not Carrier Line
DCE speed. Hence, a CH1794 will connect at a
maximum speed of 19.2kbps (result code 16). The
CH1799 will connect at a maximum DTE speed of
38.4kbps (result code of 17) and the CH2056 will
connect at a maximum speed of 57.6kbps (result code
18) unless the DTE is forced to a higher speed by
selection of data compression. In this case, the
maximum DTE to modem speed is 230.4kbps (result
code20).
Extensions to the basic result code set may be
specified by Register S95, which allows for the use of
result codes 40-64, 165-194.
IMPORTANT NOTE
Result codes 53-64 are supported by the CH1799
and CH2056. Result codes 165-194 are only
supported by the CH2056. To obtain a detailed
status report for a given modem communication
configuration, use the
AT\V1
command. Executing
this command at setup will cause the modem to
connect and return a message on line consisting of
<DTE speed> <modulation> <error protocol> <line
speed of connection>.
LEASED LINE OPTION
The CH1799LL is a leased line version of the CH1799.
Whereas the CH1799 requires an active voltage
bearing or wet PSTN line for normal operations
(typically, 48VDC on-hook line voltage), the CH1799LL
is designed to operate over a non-voltage bearing or
dry line.
The CH1799LL will only operate properly on a dry line.
Damage will occur if used on a wet line. The
CH1799LL does not support ring detect but does
support off-hook control. Refer to Cermetek
Application Note # 116 for examples and instructions
to establish a connection over a leased dry line wire
pair. Note that the length of the leased line is limited
to 20,000 feet. Use PSTN line protection as
High Speed Modem and FAX Family
2003 Cermetek Microelectronics, Inc.
Page 7
Document No. 607-0003 Revision K3 (09/03)
recommended in Figure 6B and in Cermetek
Application Note # 126. Follow all applicable
requirements for FCC Part 68 compliance. The User
is responsible to ensure that FCC Part 68 compliance
is maintained.
As an alternative, the CH1799 will operate on a leased
line if the line is made wet by application of a DC
voltage. Refer to Cermetek Application Note # 114
.
WARNING
Operation of the CH1799LL on a standard PSTN
line will damage the CH1799LL and void its
warranty. Further, operation of the CH1799LL on a
dry line without using proper current limiting circuitry
as outlined in Cermetek Application Note # 126 may
cause damage to the CH1799LL and will also void
its warranty.
Table 4. Pin Comparison of CH1786 and HS
Modem Family.
PIN
CH1786
1
RING
2
TIP
3
RXA
4
TXA
5
SPK
6
NC
7
NC
8
SLEEP
9
NC
10
TXD
11
RXD
12
V/D
13
DTR
14
DST
15
RI
16
CTS (FX only)
17
DCD
18
HS
19
V
CC
20
GND
21
RST
22
NC
NOTES:
1. * Indicates a difference between the CH1786 and
the HS Modem. The HS Modem may be directly
substituted for the CH1786 except in applications
where pins 8, 12, or 18 are used.
2. NC signifies ‘No Connect.’
3. Effective 31 March 2000, the HS Modem will no
longer support the HS indication function.
Therefore, pin 18 should be a ‘No Connect’ in all
applications.
HS Modem Family
RING
TIP
T1
NC
SPK
NC
NC
OPEN*
NC
TXD
RXD
OPEN*
DTR
DSR
RI
CTS
DCD
NC*
V
CC
GND
RST
RTS
相關PDF資料
PDF描述
CH2056TBR HIGH SPEED Modem and FAX FAMILY
CH1817 Family of Low Profile DAA Modules
CH1817-DM Family of Low Profile DAA Modules
CH1817-L Family of Low Profile DAA Modules
CH1817-LM Family of Low Profile DAA Modules
相關代理商/技術參數
參數描述
CH2056EVAL 制造商:Cermetek Microelectronics 功能描述:EVALUATION KIT FOR CH2056
CH2056TBR 制造商:Cermetek Microelectronics 功能描述:Modem, High Speed, Full Function, 56.0KBps
CH206 功能描述:重負荷電源連接器 HOODKIT206 RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型:
CH208 功能描述:重負荷電源連接器 HOODKIT208 RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型:
CH20H100R 制造商:Eaton Corporation 功能描述:1Ph/CH Loadcenter 100A 42kAIC MCB 20 Cir. Cu Bus Nema 3R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*