- 您現在的位置：買賣IC網 > PDF目錄1908 > CC-92K2-IS (Copeland Communications Inc)MODEM 56KBAUD V.90 SERIAL 3.3V PDF資料下載
參數資料
| 型號： | CC-92K2-IS |
| 廠商： | Copeland Communications Inc |
| 文件頁數： | 19/60頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODEM 56KBAUD V.90 SERIAL 3.3V |
| 標準包裝： | 30 |
| 數據格式： | V.22，V23，V.32，V.34，V.90，V.92，Bell 103，Bell 212A |
| 波特率： | 56k |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 模塊 |
| 包裝： | 散裝 |
| 其它名稱： | 539-1020 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Data Sheet
World modem II
Page 26 of 60
2004, Copeland Communications, Inc.
World modem II Datasheet Rev 1.1
Extended AT& Command Set (Command Defaults in Bold) (Continued)
Command
Action
&H7
ITU-T V.22 only (1200 bps)
&H8
Bell 212 only (1200 bps)
&H9
Bell 103 only (300 bps)
&H10
ITU-T V.21 only (300 bps)
&H11
V.23 (1200/75 bps)
&Pn
Japan pulse dialing
&P0
Configure modem for 10 pulse-per-second pulse dialing (Japan)
&P1
Configure modem for 20 pulse-per-second pulse dialing (Japan)
&Tn
Test mode
&T0
Cancel test mode (Escape to command mode to issue AT&T0). This command will also report the
number of bit errors encountered on the previous &T4 test.
&T2
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP (CC-14.4K2/CC-33K2/CC-56K2 only). The modem echoes data from TX pin back to RX pin.
&T3
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP, DAA interface section, DAA interface and analog hybrid circuit. The modem echoes data
from TX pin back to RX pin.
Initiate transmit as originating modem with automatic data generation. Modulation, data rate and
symbol rate are set by &H, &G and S41. Data pattern is set by the S40 register. Continues until
the ATH command is sent after an escape into command mode.
&T4
Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the
test using &T0.
Initiate transmit as answering modem with automatic data generation. Modulation, data rate, and
symbol rate are set by &H, &G and S41. Data pattern is set by the S40 register. Continues until
ATH command is sent after escape into command mode.
&T5
Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the
test using &T0.
&T6
Compute checksum for firmware-upgradeable section of program memory. If no firmware upgrade
is installed, &T6 returns 0x0408.
&Xn
Automatic determination of telephone line type.
&X0
Abort &x1 or &x2 command
相關PDF資料 |
PDF描述 |
|---|---|
| CC-MX-LB69-ZM | CONNECTCORE I.MX51 MODULE |
| CD22M3494MQZ96 | IC CROSSPOINT SWITCH 16X8 44PLCC |
| CD4052BPWRE4 | IC MUX/DEMUX DUAL 4X1 16TSSOP |
| CENGLH79520-10-403HC | CARD ENGINE 32MB SDRAM |
| CLC014AJE-TR13/NOPB | IC CABLE EQUALIZER ADAPT 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CC-92K2-IS5 | 功能描述:MODEM 56KBAUD V.90 SERIAL 5V RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| CC9315-000 | 制造商:TE Connectivity 功能描述:HX-SCE-1K-2.4-50-6 |
| CC9317P | 制造商:Honeywell Sensing and Control 功能描述: |
| CC9317S | 制造商:HONEYWELL CLAROSTAT 功能描述:DAC 1-CH 7-bit 8-Pin SOIC |
| CC9318P | 制造商:Honeywell Sensing and Control 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。