- 您現在的位置：買賣IC網 > PDF目錄67391 > CBTL06121AHF (NXP Semiconductors N.V.) Gen1 hex display multiplexer PDF資料下載
參數資料
| 型號： | CBTL06121AHF |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 編、解碼器及復用、解復用 |
| 英文描述： | Gen1 hex display multiplexer |
| 封裝： | CBTL06121AHF<SOT1033-1 (HWQFN56R)|<<http://www.nxp.com/packages/SOT1033-1.html<1<Always Pb-free,;CBTL06121BHF<SOT1033-1 (HWQFN56R)|<<http://www.nxp.com/packages/SOT1033-1 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 162K |
| 代理商： | CBTL06121AHF |
CBTL06121
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 26 October 2010
12 of 20
NXP Semiconductors
CBTL06121
Gen1 hex display multiplexer
10.4 HPD input, HPD output
[1]
Low-speed input changes state on cable plug/unplug.
[2]
Time from HPD_IN changing state to HPD changing state. Includes HPD rise/fall time.
10.5 MUX select and latch input
11. Test information
11.1 Switch test fixture requirements
The test fixture for switch S-parameter measurement shall be designed and built to
specific requirements, as described below, to ensure good measurement quality and
consistency.
The test fixture shall be a FR4-based PCB of the microstrip structure; the dielectric
thickness or stack-up shall be about 4 mils.
The total thickness of the test fixture PCB shall be 1.57 mm (0.62 in).
The measurement signals shall be launched into the switch from the top of the test
fixture, capturing the through-hole stub effect.
Traces between the DUT and measurement ports (SMA or microprobe) should be
uncoupled from each other, as much as possible. Therefore, the traces should be
routed in such a way that traces will diverge from each other exiting from the switch
pin field.
The trace lengths between the DUT and measurement port shall be minimized. The
maximum trace length shall not exceed 1000 mils. The trace lengths between the
DUT and measurement port shall be equal.
All of the traces on the test board and add-in card must be held to a characteristic
impedance of 50
Ω with a tolerance of ±7%.
SMA connector is recommended for ease of use. The SMA launch structure shall be
designed to minimize the connection discontinuity from SMA to the trace. The
impedance range of the SMA seen from a TDR with a 60 ps rise time should be
within 50
Ω± 7 Ω.
Table 11.
HPD input and output characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VI
input voltage
0.3
-
3.6
V
tPD
propagation delay
from HPD_SINK to HPD_SOURCE
[2] -180
-
ps
Table 12.
SEL, LE_N input characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIH
HIGH-level input voltage
2.0
-
3.6
V
VIL
LOW-level input voltage
0
-
0.8
V
ILI
input leakage current
measured with input at
VIH(max) and VIL(min)
--
10
μA
相關PDF資料 |
PDF描述 |
|---|---|
| CBTL06121BHF | Gen1 hex display multiplexer |
| CBTL06122AHF | High-performance DisplayPort-PCIe Gen2 hex display multiplexer |
| CBTL06122BHF | High-performance DisplayPort-PCIe Gen2 hex display multiplexer |
| CBTL06DP211EE | DisplayPort Gen1 2 : 1 multiplexer |
| CBTL06DP212EE | High-performance DisplayPort Gen2 2 : 1 multiplexer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CBTL06121AHF,518 | 功能描述:編碼器、解碼器、復用器和解復用器 GEN1 HEX DISPLAY RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| CBTL06121AHF-T | 功能描述:編碼器、解碼器、復用器和解復用器 GEN1 HEX DISPLAY MULTIPLEXER RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| CBTL06121BHF | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gen1 hex display multiplexer |
| CBTL06121BHF,518 | 功能描述:編碼器、解碼器、復用器和解復用器 GEN1 HEX DISPLAY RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| CBTL06121BHF-T | 功能描述:編碼器、解碼器、復用器和解復用器 GEN1 HEX DISPLAY MULTIPLEXER RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。