- 您現在的位置：買賣IC網 > PDF目錄298944 > CAT813ZI-GT3 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | CAT813ZI-GT3 |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, MO-187, MSOP-8 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 374K |
| 代理商： | CAT813ZI-GT3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁
CAT705, CAT706, CAT813
Doc. No. MD-3030 Rev. A
8
Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
WATCHDOG TIMER
The CAT705, CAT706, & CAT813 provide a
Watchdog input (WDI). The watchdog timer function
forces RESET
(and RESET in the CAT813) signals
active when the WDI input does not have a transition
from low-to-high or high-to-low within 1.12 seconds.
Timeout of the watchdog starts when RESET
(RESET
on the CAT813) becomes inactive.
If a transition
occurs on the WDI input pin prior to the watchdog
time-out, the watchdog timer is reset and begins to
time-out again. If the watchdog timer is allowed to
time-out, then the reset output(s) will go active for tRP
and once released will repeat the watchdog timeout
process.
Figure 3 below shows a typical implementation of a
watchdog function. Any processor signal that repeats
dependant on the normal operation of the processor
or directed by the software operating on the processor
can be used to strobe the watchdog input. The most
reliable is a dedicated I/O output transitioned by a
specific software instruction.
The watchdog can be disabled by floating (or tri-
stating) the WDI input (see Figure 4). If the watchdog
is disabled the WDI pin will be pulled low for the first
7/8
th’s of the watchdog period (t
WD) and pulled high for
the last 1/8
th of the watchdog period. This pulling low
of the WDI input and then high is used to detect an
open or tri-state condition and will continue to repeat
until the WDI input is driven high or low.
For most efficient operation of devices with the
watchdog function the WDI input should be held low
the majority of the time and only strobed high as
required to reset the watchdog timer.
PIC
C
DECODER
ADDRESS
MCLR
WDO
PFO
VCC
WDI
GND
PFI
MR
RESET/RESET
CAT705
CAT706
CAT813
Figure 3. Watchdog Timer
Figure 4. Watchdog Disable Circuit
C
OUTPUT
VCC
Tristate
150k
110k
WDO
PFO
VCC
WDI
GND
PFI
MR
RESET/RESET
CAT705
CAT706
CAT813
相關PDF資料 |
PDF描述 |
|---|---|
| CAT809LSDI-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT809MEUR-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT809ZTBI-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT810RSDI-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT810RSDI | POWER SUPPLY SUPPORT CKT, PDSO3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT823 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
| CAT823_08 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
| CAT823LSDI-G | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
| CAT823LSDI-GT3 | 功能描述:監控電路 Push-Pull Low 247mW 1.2V to 5.5V RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT823LTDI-G | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
發布緊急采購，3分鐘左右您將得到回復。