
CAT808
Doc. No. 3024 Rev. A 
2 
 2006 Catalyst Semiconductor, Inc. 
Characteristics subject to change without notice 
ABSOLUTE MAXIMUM RATINGS
(1)
Parameters
Temperature under Bias 
Storage Temperature 
Voltage on any Pin with Respect to GND
(2)(3)
V
DD
 with Respect to GND 
Lead Soldering temperature (10 seconds) 
TSOT-23-5 
Power Dissipation  
SOT-89 
Ratings
-55 to +125 
-65 to +150 
-2.0 to V
DD
 + 2.0 
-2.0 to 7.0 
+300 
250 
500 
Units 
oC 
oC 
V 
V 
oC 
mW 
mW 
RECOMMENDED OPERATING CONDITIONS
Parameters
V
DD
Operating Temperature Range 
Ratings
+1.2 to +6.0 
-40 to +85 
Units 
V 
oC 
DC ELECTRICAL CHARACTERISTICS 
T
A
 = -40oC to +85oC, V
DD
 = 1.2V to 6.0V 
Symbol 
V
DET
V
DET
Parameter 
Detection Voltage, 27 
Conditions 
T
A
 = -40oC to +85oC 
T
A
 = -40oC to +85oC 
V
DD 
= 4.0V 
V
DD 
= 5.0V 
V
DD 
= 6.0V 
Min Typ. Max
2.62 2.7 2.78
Units 
Detection Voltage, 32 
3.12 3.2 3.28
V 
- 
2.4 
5 
- 
3.5 
7 
I
DD
Current Consumption 
- 
5 
10 
- 
- 
1 
60 
μA 
V
DD
=1.2V 
V
DD
=2.4V 
0.6 
2.9 
- 
- 
1.4 
5 
- 
- 
I
OUT
Output SinkCurrent 
V
DS
 = 0.5V 
mA 
I
LEAK
T
PHL/LH
Δ
  - V
DET 
Δ
T
A
●
 -V
DET
Output Leakage Current 
Response Time 
Detection Voltage 
Temperature Coefficient
(4)
V
DS
 = 5.0V, V
DD
 = 5.0V 
– 
μA 
μs 
T
A
 = -40oC to +85oC 
- 
±10 ±100 ppm/oC
Notes: 
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings 
only and functional operation of the devices at these or any other conditions outside of those listed in the operational sections of  this 
specification is not  implied. Exposure to any absolute maximum rating for extended periods may affect device performance and 
reliability. 
(2) The Minimum DC input voltage is -0.5V.  During transitions, inputs may undershoot to -2.0V for periods of less than 20ns. Maximum DC 
voltage on output pins is V
CC
 +0.5V, which may overshoot to V
CC
 +2.0V for periods of less than 20ns. 
(3) Latch-up protection is provided for stresses up to 100mA on all pins from -1V to V
CC
 +1V. 
(4) The temperature change ratio in the detection voltage [ppm/°C] is calculated by using the following equation: 
]
C
/o
ppm
[
000
,
000
,
×
V
-
T
V
DET
A
DET
Δ
Δ