- 您現在的位置：買賣IC網 > PDF目錄366750 > CAT64LC40JI 36-Mbit DDR-II SIO SRAM 2-Word Burst Architecture PDF資料下載
參數資料
| 型號： | CAT64LC40JI |
| 英文描述： | 36-Mbit DDR-II SIO SRAM 2-Word Burst Architecture |
| 中文描述： | SPI串行EEPROM |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 140K |
| 代理商： | CAT64LC40JI |
7
CAT64LC10/20/40
Doc. No. 1021, Rev. A
a 16-bit data field is also required following the 8-bit
address field.
The CAT64LC10/20/40 requires an active LOW
CS
in
order to be selected. Each instruction must be preceded
by a HIGH-to-LOW transition of
CS
before the input of
the 4-bit start sequence. Prior to the 4-bit start sequence
(1010), the device will ignore inputs of all other logical
sequence.
Figure 4. Write Instruction Timing
Figure 5. Ready/
BUSY
Status Instruction Timing
Read
Upon receiving a READ command and address (clocked
into the DI pin), the DO pin will output data one t
PD
after
the falling edge of the 16th clock (the last bit of the
address field). The READ operation is not affected by
the RESET input.
Write
After receiving a WRITE op code, address and data, the
device goes into the AUTO-Clear cycle and then the
* Please check instruction set table for address
SK
DI
CS
DO
RESET
1
0
1
0
0
1
0
0
ADDRESS*
D15
D0
RDY/
BUSY
SK
DI
CS
DO
RESET
WRITE INSTRUCTION
NEXT INSTRUCTION
HIGH
LOW
RDY/
BUSY
相關PDF資料 |
PDF描述 |
|---|---|
| CAT64LC40JI-2.5 | SPI Serial EEPROM |
| CAT64LC40JI-TE13 | SPI Serial EEPROM |
| CAT64LC40JI-TE7 | SPI Serial EEPROM |
| CAT64LC40J-TE13 | SPI Serial EEPROM |
| CAT64LC40J-TE7 | SPI Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT64LC40JI-2.5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| CAT64LC40JI-GT3 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:4 kb SPI Serial EEPROM |
| CAT64LC40JI-T3 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:4 kb SPI Serial EEPROM |
| CAT64LC40JITE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:1K/2K/4K-Bit SPI Serial E2PROM |
| CAT64LC40JI-TE13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。