- 您現在的位置：買賣IC網 > Datasheet目錄39 > CAT6095VP2-GT4 (ON Semiconductor)IC TEMP SENSOR STAND ALONE 8TDFN Datasheet資料下載
參數資料
| 型號： | CAT6095VP2-GT4 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 151K |
| 描述： | IC TEMP SENSOR STAND ALONE 8TDFN |
| 標準包裝： | 1 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±3°C（最小值） |
| 拓撲： | ADC（三角積分型），比較器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN（2x3） |
| 包裝： | 標準包裝 |
| 其它名稱： | CAT6095VP2-GT4OSDKR |
CAT6095
http://onsemi.com
5
Pin Description
SCL: The Serial Clock input pin accepts the Serial Clock
generated by the Master (Host).
SDA: The Serial Data I/O pin receives input data and
transmits data stored in the internal registers. In transmit
mode, this pin is open drain. Data is acquired on the positive
edge, and is delivered on the negative edge of SCL.
A0, A1 and A2: The Address pins set the device address.
These pins have onchip pulldown resistors.
EVENT
: The opendrain EVENT
pin can be programmed
to signal over/under temperature limit conditions.
PowerOn Reset
The CAT6095 incorporates PowerOn Reset (POR)
circuitry which monitors the supply voltage, and then resets
(initializes) the internal state machine below a POR trigger
level of approximately 2.0 V, i.e. well below the minimum
recommended V
CC
value.
The temperature sensor (TS) powers-up into conversion
mode. The internal state machine will operate properly
above the POR trigger level, but valid temperature readings
can be expected only after the first conversion cycle started
and completed at nominal supply voltage.
Device Interface
The CAT6095 supports I
2
C and SMBus data transmission
protocols. These protocols describe serial communication
between transmitters and receivers sharing a 2wire data
bus. Data ow is controlled by a Master device, which
generates the serial clock and the START and STOP
conditions. The CAT6095 acts as a Slave device. Master and
Slave alternate as transmitter and receiver. Up to 8 CAT6095
devices may be present on the bus simultaneously, and can
be individually addressed by matching the logic state of the
address inputs A0, A1, and A2.
I
2
C/SMBus Protocol
The I
2
C/SMBus uses two wires, one for clock (SCL) and
one for data (SDA). The two wires are connected to the V
CC
supply via pullup resistors. Master and Slave devices
connect to the bus via their respective SCL and SDA pins.
The transmitting device pulls down the SDA line to
transmit a 0 and releases it to transmit a 1.
Data transfer may be initiated only when the bus is not
busy (see A.C. Characteristics).
During data transfer, the SDA line must remain stable
while the SCL line is HIGH. An SDA transition while SCL
is HIGH will be interpreted as a START or STOP condition
(Figure 8).
START
The START condition precedes all commands. It consists
of a HIGH to LOW transition on SDA while SCL is HIGH.
The START acts as a wakeup call to all Slaves. Absent a
START, a Slave will not respond to commands.
STOP
The STOP condition completes all commands. It consists
of a LOW to HIGH transition on SDA while SCL is HIGH.
The STOP tells the Slave that no more data will be written
to or read from the Slave.
Device Addressing
The Master initiates data transfer by creating a START
condition on the bus. The Master then broadcasts an 8bit
serial Slave address. The first 4 bits of the Slave address (the
preamble) select the Temperature Sensor (TS preamble =
0011) as shown in Figure 9. The next 3 bits, A2, A1 and A0,
select one of 8 possible TS Slave devices. The last bit, R/W
,
species whether a Read (1) or Write (0) operation is being
performed.
Acknowledge
A matching Slave address is acknowledged (ACK) by the
Slave by pulling down the SDA line during the 9
th
clock
cycle (Figure 10). After that, the Slave will acknowledge all
data bytes sent to the bus by the Master. When the Slave is
the transmitter, the Master will in turn acknowledge data
bytes in the 9
th
clock cycle. The Slave will stop transmitting
after the Master does not respond with acknowledge
(NoACK) and then issues a STOP. Bus timing is illustrated
in Figure 11.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1621S+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS1624S+T&R | IC THERM/EEPROM DIG 256BYT 8SOIC |
| DS1626S+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS1629S+T&R | IC THERM/RTC/CALENDAR DIG 8-SOIC |
| DS1631S+T&R | IC THERMOMETER DIG HI-PREC 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT6095VP2I-GT4 | 功能描述:板上安裝溫度傳感器 Dig Output Temp Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| CAT6201 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:300 mA / 13 V Adjustable CMOS LDO Regulator |
| CAT6201VP2.GT3 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:300 mA / 13 V Adjustable CMOS LDO Regulator |
| CAT6201VP2GT3 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:300 mA / 13 V Adjustable CMOS LDO Regulator |
| CAT6201VP2-GT3 | 功能描述:低壓差控制器 - LDO LDO 300 MA ADJUSTABLE RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節: 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
發布緊急采購，3分鐘左右您將得到回復。