- 您現在的位置：買賣IC網 > PDF目錄369656 > CAT5269UI-10TE13 Dual Digitally Programmable Potentiometers (DPP) with 64 Taps and 2-wire Interface PDF資料下載
參數資料
| 型號： | CAT5269UI-10TE13 |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual Digitally Programmable Potentiometers (DPP) with 64 Taps and 2-wire Interface |
| 中文描述： | 雙數字可編程電位計（民進黨）與64個龍頭和2線接口 |
| 文件頁數： | 9/18頁 |
| 文件大?。?/td> | 95K |
| 代理商： | CAT5269UI-10TE13 |
9
CAT5419
Document No. 2115, Rev. F
Table 3. Instruction Set
WIPER CONTROL AND DATA REGISTERS
Wiper Control Register (WCR)
The CAT5419 contains two 6-bit Wiper Control Registers,
one for each potentiometer. The Wiper Control Register
output is decoded to select one of 64 switches along its
resistor array. The contents of the WCR can be altered
in four ways: it may be written by the host via Write Wiper
Control Register instruction; it may be written by
transferring the contents of one of four associated Data
Registers via the XFR Data Register instruction, it can be
modified one step at a time by the Increment/decrement
instruction (see Instruction section for more details).
Finally, it is loaded with the content of its data register
zero (DR0) upon power-up.
The Wiper Control Register is a volatile register that
loses its contents when the CAT5419 is powered-down.
Although the register is automatically loaded with the
value in DR0 upon power-up, this may be different from
the value present at power-down.
Data Registers (DR)
Each potentiometer has four 6-bit non-volatile Data
Registers. These can be read or written directly by the
host. Data can also be transferred between any of the
four Data Registers and the associated Wiper Control
Register. Any data changes in one of the Data Registers
is a non-volatile operation and will take a maximum of
5ms.
If the application does not require storage of multiple
settings for the potentiometer, the Data Registers can be
used as standard memory locations for system
parameters or user preference data.
INSTRUCTIONS
Four of the nine instructions are three bytes in length.
These instructions are:
—
Read Wiper Control Register
- read the current
wiper position of the selected potentiometer in the WCR
—
Write Wiper Control Register
- change current
wiper position in the WCR of the selected potentiometer
—
Read Data Register
- read the contents of the
selected Data Register
—
Write Data Register
- write a new value to the
selected Data Register
The basic sequence of the three byte instructions is
illustrated in Figure 8. These three-byte instructions
Note:
1/0 = data is one or zero
Instruction
Instruction Set
Operation
I3
1
I2
0
I1
0
I0
1
R1
0
R0
0
Read Wiper Control
Register
Write Wiper Control Register
0
1/0
Read the contents of the Wiper Control
Register pointed to by P0
Write new value to the Wiper Control
Register pointed to by P0
Read the contents of the Data Register
pointed to by P0 and R1-R0
Write new value to the Data Register
pointed to by P0 and R1-R0
Transfer the contents of the Data Register
pointed to by P0 and R1-R0 to its
associated Wiper Control Register
Transfer the contents of the Wiper Control
Register pointed to by P0 to the Data
Register pointed to by R1-R0
Transfer the contents of the Data Registers
pointed to by R1-R0 of both pots to their
respective Wiper Control Register
Transfer the contents of both Wiper Control
Registers to their respective data Registers
pointed to by R1-R0 of both pots
Enable Increment/decrement of the Control
Latch pointed to by P0
1
0
1
0
0
0
0
1/0
Read Data Register
1
0
1
1
1/0
1/0
0
1/0
Write Data Register
1
1
0
0
1/0
1/0
0
1/0
XFR Data Register to Wiper
Control Register
1
1
0
1
1/0
1/0
0
1/0
XFR Wiper Control Register
to Data Register
1
1
1
0
1/0
1/0
0
1/0
Gang XFR Data
Registers
to Wiper Control Registers
0
0
0
1
1/0
1/0
0
0
Gang XFR Wiper Control
Registers to Data Register
1
0
0
0
1/0
1/0
0
0
Increment/Decrement Wiper
Control Register
0
0
1
0
0
0
0
1/0
WCR0/
P0
0
相關PDF資料 |
PDF描述 |
|---|---|
| CAT5269UI-25TE13 | Dual Digitally Programmable Potentiometers (DPP) with 64 Taps and 2-wire Interface |
| CAT809LEUR-T10 | 3-Pin Microprocessor Power Supply Supervisors |
| CAT809JEXR-T | 3-Pin Microprocessor Power Supply Supervisors |
| CAT809JEXR-T10 | 3-Pin Microprocessor Power Supply Supervisors |
| CAT809LEUR-T | 3-Pin Microprocessor Power Supply Supervisors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT5269WI00 | 制造商:ON Semiconductor 功能描述:DPP, NV, DUAL 256 TAPS, I2C - Rail/Tube |
| CAT5269WI-00-T1 | 功能描述:數字電位計 IC DPP NV DUAL 256 TAP I2C RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5269WI50 | 功能描述:數字電位計 IC Ind Temp 50K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5269WI-50 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT5269WI-50-T1 | 功能描述:數字電位計 IC DPP NV DUAL 256 TAP I2C RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。