- 您現在的位置：買賣IC網 > PDF目錄366746 > CAT5261JI-50TE13 Replaced by DSD1794A : 132dB SNR Highest Performance Stereo Audio DAC (H/W Control) 28-SSOP PDF資料下載
參數資料
| 型號： | CAT5261JI-50TE13 |
| 英文描述： | Replaced by DSD1794A : 132dB SNR Highest Performance Stereo Audio DAC (H/W Control) 28-SSOP |
| 中文描述： | 雙數字可編程電位器 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 95K |
| 代理商： | CAT5261JI-50TE13 |
8
CAT5261
Document No. 2122, Rev. B
INSTRUCTION AND REGISTER
DESCRIPTION
DEVICE TYPE / ADDRESS BYTE
The first byte sent to the CAT5261 from the master/
processor is called the Device Address Byte. The most
significant four bits of the Device Type address are a
device type identifier. These bits for the CAT5261 are
fixed at 0101[B] (refer to Table 1).
The two least significant bits in the slave address byte,
A1 - A0, are the internal slave address and must match
the physical device address which is defined by the state
of the A1 - A0 input pins for the CAT5261 to successfully
continue the command sequence. Only the device which
slave address matches the incoming device address
sent by the master executes the instruction. The A1 - A0
inputs can be actively driven by CMOS input signals or
tied to V
CC
or V
SS
. The remaining two bits in the device
address byte must be set to 0.
INSTRUCTION BYTE
The next byte sent to the CAT5261 contains the instruction
and register pointer information. The four most significant
bits used provide the instruction opcode I3 - I0. The R1
and R0 bits point to one of the four data registers of each
associated potentiometer. The least two significant bits
point to one of two Wiper Control Registers. The format
is shown in Table 2.
Table 1. Identification Byte Format
ID3
0
(MSB)
ID2
1
ID1
0
ID0
1
0
0
A1
A0
(LSB)
Device Type
Identifier
Slave Address
Table 2. Instruction Byte Format
I3
I2
I1
I0
R1
R0
P1
P0
(MSB)
(LSB)
Instruction
Opcode
Data Register
Selection
WCR/Pot Selection
Data Register Selection
Data Register Selected
R1
R0
DR0
0
0
DR1
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| CAT5261WI-50TE13 | Dual Digitally Programmable Potentiometer |
| CAT5261YI-00TE13 | Dual Digitally Programmable Potentiometer |
| CAT5261YI-50TE13 | Dual Digitally Programmable Potentiometer |
| CAT5261JI-00TE13 | Dual Digitally Programmable Potentiometer |
| CAT5261UI-00TE13 | Dual Digitally Programmable Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT5261WI00 | 功能描述:數字電位計 IC DPP NV Dual 256 taps SPI RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5261WI-00 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT5261WI-00-T1 | 功能描述:數字電位計 IC DPP NV DUAL 256 TAP SPI RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5261WI50 | 功能描述:數字電位計 IC Ind Temp 50K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| CAT5261WI-50 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。