- 您現在的位置：買賣IC網 > PDF目錄366709 > CAT25C128LI-GT3 128K/256K-Bit SPI Serial CMOS EEPROM PDF資料下載
參數資料
| 型號： | CAT25C128LI-GT3 |
| 英文描述： | 128K/256K-Bit SPI Serial CMOS EEPROM |
| 中文描述： | 128K/256K-Bit SPI串行EEPROM中的CMOS |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 454K |
| 代理商： | CAT25C128LI-GT3 |
CAT25C128/256
10
Document No. 1018, Rev. I
CS
SCK
HOLD
SO
tCD
tHD
tHD
tCD
tLZ
tHZ
HIGH IMPEDANCE
Note: Dashed Line= mode (1, 1)
—
— — —
Figure 9.
HOLD
Timing
Figure 10.
WP
Timing
t
CSH
SCK
WP
t
WPS
t
WPH
Note: Dashed Line= mode (1, 1)
—
— — —
DESIGN CONSIDERATIONS
If an invalid op code is received, no data will be shifted
into the CAT25C128/256, and the serial output pin (SO)
will remain in a high impedence state until the falling
edge of
CS
is detected again.
When powering down, the supply should be taken down
to 0V, so that the CAT25C128/256 will be reset when
power is ramped back up. If this is not possible, then,
following a brown-out episode, the CAT25C128/256
can be reset by refreshing the contents of the Status
Register (See Application Note AN10).
The CAT25C128/256 powers up in a write disable state
and in a low power standby mode. A WREN instruction
must be issued to perform any writes to the device after
power up. Also,on power up
CS
should be brought low
to enter a ready state and receive an instruction. After
a successful byte/page write or status register write the
CAT25C128/256 goes into a write disable mode.
CS
must be set high after the proper number of clock cycles
to start an internal write cycle. Access to the array during
an internal write cycle is ignored and program-ming
is continued. On power up, SO is in a high impedance.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT25C256LI-1.8-GT2 | 128K/256K-Bit SPI Serial CMOS EEPROM |
| CAT25C256LI-1.8-GT3 | 128K/256K-Bit SPI Serial CMOS EEPROM |
| CAT25C256LI-1.8T2 | 128K/256K-Bit SPI Serial CMOS EEPROM |
| CAT25C256LI-1.8T3 | 128K/256K-Bit SPI Serial CMOS EEPROM |
| CAT25C256LI-GT2 | 128K/256K-Bit SPI Serial CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT25C128P | 功能描述:電可擦除可編程只讀存儲器 (16kx8) 128K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C128P-1.8 | 功能描述:電可擦除可編程只讀存儲器 (16kx8) 128K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C128PA | 功能描述:電可擦除可編程只讀存儲器 (16kx8) 128K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C128PI | 功能描述:電可擦除可編程只讀存儲器 (16kx8) 128K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C128PI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (16kx8) 128K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。