- 您現在的位置：買賣IC網 > PDF目錄352981 > CAT25C03U14I-TE13 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM PDF資料下載
參數資料
| 型號： | CAT25C03U14I-TE13 |
| 元件分類： | EEPROM |
| 英文描述： | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
| 中文描述： | 1K/2K/4K/8K/16K SPI 串行 互補型金屬氧化物 電可擦可編程只讀存儲器 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 77K |
| 代理商： | CAT25C03U14I-TE13 |
5
CAT25010/20/40
Doc. No. 1006, Rev. G
Status Register Bits
Array Address
Protection
BP1
BP0
Protected
0
None
No Protection
0
1
25010: 60-7F
Quarter Array Protection
25020: C0-FF
25040: 180-1FF
1
0
25010: 40-7F
Half Array Protection
25020: 80-FF
25040: 100-1FF
1
25010: 00-7F
Full Array Protection
25020: 00-FF
25040: 000-1FF
BLOCK PROTECTION BITS
76543210
1111
BP1
BP0
WEL
RDY
STATUS REGISTER
clock for SPI modes (0,0 & 1,1).
SCK: Serial Clock
SCK is the serial clock pin. This pin is used to synchronize
the communication between the microcontroller and the
CAT25010/20/40. Opcodes, byte addresses, or data
present on the SI pin are latched on the rising edge of the
SCK. Data on the SO pin is updated on the falling edge
of the SCK for SPI modes (0,0 & 1,1) .
CS
CS: Chip Select
CS is the Chip select pin. CS low enables the CAT25010/
20/40 and
CS high disables the CAT25010/20/40. CS
high takes the SO output pin to high impedance and
forces the devices into a Standby Mode (unless an
internal write operation is underway) The CAT25010/
20/40 draws ZERO current in the Standby mode. A high
to low transition on
CS is required prior to any sequence
being initiated. A low to high transition on
CS after a valid
write sequence is what initiates an internal write cycle.
WP
WP: Write Protect
WP is the Write Protect pin. The Write Protect pin will
allow normal read/write operations when held high.
When
WP is tied low all write operations are inhibited.
WP held low while CS is low will interrupt a write to the
CAT25010/20/40. If the internal write cycle has already
been initiated,
WP going low will have no effect on any
write operation. Figure 10 illustrates the
WP timing
sequence during a write operation.
HOLD
HOLD: Hold
The
HOLD pin is used to pause transmission to the
CAT25010/20/40 while in the middle of a serial sequence
without having to re-transmit entire sequence at a later
time. To pause,
HOLD must be brought low while SCK
is low. The SO pin is in a high impedance state during
the time the part is paused, and transitions on the SI pins
will be ignored. To resume communication,
HOLD is
brought high, while SCK is low. (
HOLD should be held
high any time this function is not being used.)
HOLD may
be tied high directly to VCC or tied to VCC through a
resistor. Figure 9 illustrates hold timing sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT25C03UA-1.8TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
| CAT25C03UA-TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
| CAT25C03UI-1.8TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
| CAT25C03VI-TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
| CAT25C03YE-TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT25C03UA | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C03UI | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C03UI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 1.8-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C03V | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C03V-1.8 | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 1.8-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。