- 您現在的位置：買賣IC網 > PDF目錄366693 > CAT24WC16WATE13F 1K/2K/4K/8K/16K-Bit Serial EEPROM PDF資料下載
參數資料
| 型號： | CAT24WC16WATE13F |
| 英文描述： | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| 中文描述： | 1K/2K/4K/8K/16K-Bit串行EEPROM |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 518K |
| 代理商： | CAT24WC16WATE13F |
CAT24WC01/02/04/08/16
6
Doc. No. 1022, Rev. N
2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
address. The CAT24WC01/02/04/08/16 then performs
a Read or Write operation depending on the state of the
R/
W
bit.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24WC01/02/04/08/16 responds with an ac-
knowledge after receiving a START condition and its
slave address. If the device has been selected along
with a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT24WC01/02/04/08/16 is in a READ mode
it transmits 8 bits of data, releases the SDA line, and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT24WC01/02/04/08/16 will
continue to transmit data. If no acknowledge is sent by
the Master, the device terminates data transmission and
waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/
W
bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
the byte address that is to be written into the address
pointer of the CAT24WC01/02/04/08/16. After receiving
another acknowledge from the Slave, the Master device
transmits the data byte to be written into the addressed
memory location. The CAT24WC01/02/04/08/16 ac-
knowledge once more and the Master generates the
STOP condition, at which time the device begins its
internal programming cycle to nonvolatile memory. While
this internal cycle is in progress, the device will not
respond to any request from the Master device.
Page Write
The CAT24WC01/02/04/08/16 writes up to 16 bytes of
data in a single write cycle, using the Page Write
operation. The Page Write operation is initiated in the
same manner as the Byte Write operation, however
instead of terminating after the initial word is transmitted,
Figure 5. Slave Address Bits
*
**
*** A0, A1 and A2 must compare to its corresponding hard wired input pins (pins 1, 2 and 3).
A0, A1 and A2 correspond to pin 1, pin 2 and pin 3 of the device.
a8, a9 and a10 correspond to the address of the memory array address word.
1
0
1
0
A2 A1 A0
R/W
1
0
1
0
A2
A1
a8
R/W
1
0
1
0
A2
a9 a8
R/W
1
0
1
0
a10
a9
a8
R/W
CAT24WC01/02
CAT24WC04
CAT24WC08
CAT24WC16
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24WC16WETE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16WITE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16YATE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16YETE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16YITE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24WC16WI | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC16WI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC16WI-TE13 | 制造商:ON Semiconductor 功能描述:EEPROM Serial-I2C 16K-Bit 2K x 8 3.3V/5V 8-Pin SOIC N T/R |
| CAT24WC16W-TE13 | 制造商:ON Semiconductor 功能描述:EEPROM Serial-I2C 16K-Bit 2K x 8 3.3V/5V 8-Pin SOIC N T/R |
| CAT24WC256K | 功能描述:電可擦除可編程只讀存儲器 (768x8) 256k 32 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。