- 您現在的位置：買賣IC網 > PDF目錄366693 > CAT24WC16PATE13F 1K/2K/4K/8K/16K-Bit Serial EEPROM PDF資料下載
參數資料
| 型號： | CAT24WC16PATE13F |
| 英文描述： | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| 中文描述： | 1K/2K/4K/8K/16K-Bit串行EEPROM |
| 文件頁數： | 5/14頁 |
| 文件大小： | 518K |
| 代理商： | CAT24WC16PATE13F |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
CAT24WC01/02/04/08/16
5
Doc. No. 1022, Rev. N
2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
using either CAT24WC01 or CAT24WC02 device. All
three address pins are used for these densities. If only
one CAT24WC01 or CAT24WC02 is addressed on the
bus, all three address pins (A0, A1and A2) can be left
floating or connected to V
SS
.
A total of four devices can be addressed on a single bus
when using CAT24WC04 device. Only A1 and A2
address pins are used with this device. The A0 address
pin is a no connect pin and can be tied to V
SS
or left
floating. If only one CAT24WC04 is being addressed on
the bus, the address pins (A1 and A2) can be left floating
or connected to V
SS
.
Only two devices can be cascaded when using
CAT24WC08. The only address pin used with this
device is A2. The A0 and A1 address pins are no
connect pins and can be tied to V
SS
or left floating. If only
one CAT24WC08 is being addressed on the bus, the
address pin (A2) can be left floating or connected to V
SS
.
The CAT24WC16 is a stand alone device. In this case,
all address pins (A0, A1and A2) are no connect pins and
can be tied to V
SS
or left floating.
WP:
Write Protect
If the WP pin is tied to V
CC
the entire memory array
becomes Write Protected (READ only). When the WP
pin is tied to V
SS
or left floating normal read/write
operations are allowed to the device.
I
2
C Bus Protocol
The following defines the features of the I
2
C bus protocol:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes
in the data line while the clock line is high will be
interpreted as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24WC01/02/04/08/16
monitor the SDA and SCL lines and will not respond until
this condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The bus Master begins a transmission by sending a
START condition. The Master then sends the address
of the particular slave device it is requesting. The four
most significant bits of the 8-bit slave address are fixed
as 1010 for the CAT24WC01/02/04/08/16 (see Fig. 5).
The next three significant bits (A2, A1, A0) are the device
address bits and define which device or which part of the
device the Master is accessing. Up to eight CAT24WC01/
02, four CAT24WC04, two CAT24WC08, and one
CAT24WC16 may be individually addressed by the
system. The last bit of the slave address specifies
whether a Read or Write operation is to be performed.
When this bit is set to 1, a Read operation is selected,
and when set to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT24WC01/02/04/08/16 monitors
the bus and responds with an acknowledge (on the SDA
line) when its address matches the transmitted slave
Figure 4. Acknowledge Timing
5020 FHD F06
ACKNOWLEDGE
1
START
SCL FROM
MASTER
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24WC16PETE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16PITE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16RATE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16RETE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC16RITE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24WC16PI | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC16PI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC16W | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC16W-1.8 | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC16WA | 功能描述:電可擦除可編程只讀存儲器 (2048x8) 16k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。