- 您現在的位置：買賣IC網 > PDF目錄169495 > CAT24WC128XI-TE13 16K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | CAT24WC128XI-TE13 |
| 元件分類： | PROM |
| 英文描述： | 16K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封裝： | LEAD AND HALOGEN FREE, EIAJ, SOIC-8 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 506K |
| 代理商： | CAT24WC128XI-TE13 |
CAT24WC128
5
Doc. No. 1038, Rev. B
1
010
A2
A1
A0
R/W
DEVICE ADDRESSING
The bus Master begins a transmission by sending a
START condition. The Master sends the address of the
particular slave device it is requesting. The seven most
significant bits of the 8-bit slave address are fixed as
1010XXX (Fig. 5), where X can be a 0 or 1. The last bit
of the slave address specifies whether a Read or Write
operation is to be performed. When this bit is set to 1, a
Read operation is selected, and when set to 0, a Write
operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT24WC128 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT24WC128 then performs a Read or Write operation
depending on the state of the R/W bit.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24WC128 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation,
it responds with an acknowledge after receiving each 8-
bit byte.
When the CAT24WC128 begins a READ mode it trans-
mits 8 bits of data, releases the SDA line, and monitors
the line for an acknowledge. Once it receives this ac-
Figure 4. Acknowledge Timing
Figure 5. Slave Address Bits
ACKNOWLEDGE
1
START
SCL FROM
MASTER
89
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
knowledge, the CAT24WC128 will continue to transmit
data. If no acknowledge is sent by the Master, the device
terminates data transmission and waits for a STOP
condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/W bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
two 8-bit address words that are to be written into the
address pointers of the CAT24WC128. After receiving
another acknowledge from the Slave, the Master device
transmits the data to be written into the addressed
memory location. The CAT24WC128 acknowledges
once more and the Master generates the STOP condi-
tion. At this time, the device begins an internal program-
ming cycle to nonvolatile memory. While the cycle is in
progress, the device will not respond to any request from
the Master device.
Page Write
The CAT24WC128 writes up to 64 bytes of data, in a
single write cycle, using the Page Write operation. The
page write operation is initiated in the same manner as
the byte write operation, however instead of terminating
after the initial byte is transmitted, the Master is allowed
to send up to 63 additional bytes. After each byte has
been transmitted, CAT24WC128 will respond with an
XXX
X is Don't Care, can be a '0' or a '1'.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24WC257J-3TE13REVA | 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC33XI-1.8 | 4K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC65K-TE13 | 8K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC64PE-1.8REVD | 8K X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| CAT25040LI-GTD | 128 X 8 SPI BUS SERIAL EEPROM, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24WC129J | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC129J-1.8 | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC129JA | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC129JI | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC129JI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。