- 您現在的位置：買賣IC網 > PDF目錄366693 > CAT24WC12833JA-1.8TE13 128K-Bit I2C Serial CMOS EEPROM PDF資料下載
參數資料
| 型號： | CAT24WC12833JA-1.8TE13 |
| 英文描述： | 128K-Bit I2C Serial CMOS EEPROM |
| 中文描述： | 128K的位I2C串行CMOS EEPROM的 |
| 文件頁數： | 4/9頁 |
| 文件大小： | 414K |
| 代理商： | CAT24WC12833JA-1.8TE13 |
CAT24WC128
4
Doc. No. 1038, Rev. E
WP:
Write Protect
This input, when tied to GND, allows write operations to
the entire memory. When this pin is tied to Vcc, the
entire memory is write protected. When left floating,
memory is unprotected.
Figure 3. Start/Stop Timing
Figure 2. Write Cycle Timing
Figure 1. Bus Timing
START BIT
SDA
STOP BIT
SCL
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
ACK
8TH BIT
BYTE n
SCL
SDA
tHIGH
SCL
SDA IN
SDA OUT
tLOW
tF
tLOW
tR
tBUF
tSU:STO
tSU:DAT
tHD:DAT
tHD:STA
tSU:STA
tAA
tDH
I
2
C BUS PROTOCOL
The features of the I
2
C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus
is not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes
in the data line while the clock line is high will be
interpreted as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24WC128 monitors
the SDA and SCL lines and will not respond until this
condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must
end with a STOP condition.
PIN DESCRIPTIONS
SCL:
Serial Clock
The serial clock input clocks all data transferred into or
out of the device.
SDA:
Serial Data/Address
The bidirectional serial data/address pin is used to
transfer all data into and out of the device. The SDA pin
is an open drain output and can be wire-ORed with
other open drain or open collector outputs.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24WC12833JATE13 | 128K-Bit I2C Serial CMOS EEPROM |
| CAT24WC12865XI-1.8TE13 | 128K-Bit I2C Serial CMOS EEPROM |
| CAT24WC12865XITE13 | 128K-Bit I2C Serial CMOS EEPROM |
| CAT24WC12865YA-1.8TE13 | 128K-Bit I2C Serial CMOS EEPROM |
| CAT24WC12865YATE13 | 128K-Bit I2C Serial CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24WC128J | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC128J-1.8 | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC128JA | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC128JI | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC128JI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (384x8) 128k 16 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。