- 您現在的位置：買賣IC網 > PDF目錄227848 > CAT24C083JA-28TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | CAT24C083JA-28TE13 |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 85K |
| 代理商： | CAT24C083JA-28TE13 |
CAT24C163/083/043/023
7
Advanced
Doc. No. 25080-00 3/98 M-1
ACKNOWLEDGE
1
START
SCL FROM
MASTER
89
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
Figure 5. Acknowledge Timing
Figure 6. Slave Address Bits
FUNCTIONAL DESCRIPTION
The CAT24CXXX supports the I2C Bus data transmis-
sion protocol. This Inter-Integrated Circuit Bus protocol
defines any device that sends data to the bus to be a
transmitter and any device receiving data to be a re-
ceiver. The transfer is controlled by the Master device
which generates the serial clock and all START and
STOP conditions for bus access. The CAT24CXXX
operates as a Slave device. Both the Master device and
Slave device can operate as either transmitter or re-
ceiver, but the Master device controls which mode is
activated.
I2C BUS PROTOCOL
The features of the I2C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes in
the data line while the clock line is high will be interpreted
as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24CXXX monitors the
SDA and SCL lines and will not respond until this
condition is met.
* 'X' Corresponds to Don't Care Bits (can be a zero or a one)
** a8, a9 and a10 correspond to the address of the memory array address word.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particu-
lar slave device it is requesting. The four most significant
bits of the 8-bit slave address are fixed as 1010.
The next three bits (Fig. 6) define memory addressing.
For the 24C023, the three bits are don't care. For the
24C043, the next two bits are don't care and the third bit
is the high order address bit. For the 24C083, the next
bit is don't care and the successive bits define the higher
order address bits. For the 24C163 the three bits define
higher order bits.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this
bit is set to 1, a Read operation is selected, and when set
to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT24CXXX monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT24CXXX then performs a Read or Write operation
depending on the state of the R/
W bit.
1
010
X
R/W
1
0
1
0
X
a8
R/W
24C023
24C043
1
010
X
a9
a8
R/W
1
0
1
0
a10
a9
a8
R/W
24C083
24C163
相關PDF資料 |
PDF描述 |
|---|---|
| CP4660-7RDVG | 4-OUTPUT 168 W DC-DC REG PWR SUPPLY MODULE |
| CP4660-9VGTI | 4-OUTPUT 168 W DC-DC REG PWR SUPPLY MODULE |
| CTDD1907SF-241212-T1K-2 | 2-OUTPUT 2 W DC-DC UNREG PWR SUPPLY MODULE |
| CTDD2210SF-1515-D1.5K-2 | 2-OUTPUT 2 W DC-DC REG PWR SUPPLY MODULE |
| CAT1027PE-45 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24C08C4ATR | 功能描述:電可擦除可編程只讀存儲器 8KB I2C SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24C08C4CTR | 制造商:ON Semiconductor 功能描述:8KB I2C SER EEPROM - Tape and Reel 制造商:ON Semiconductor 功能描述:EEPROM 8KB I2C SER EEPROM 制造商:ON Semiconductor 功能描述:DSFTP / 8KB I2C SER EEPROM |
| CAT24C08C5ATR | 制造商:ON Semiconductor 功能描述:8KB I2C SER EEPROM - Tape and Reel 制造商:ON Semiconductor 功能描述:EEPROM 8KB I2C SER EEPROM 制造商:ON Semiconductor 功能描述:DSFTP / 8KB I2C SER EEPROM |
| CAT24C08HU4I-GT3 | 功能描述:電可擦除可編程只讀存儲器 8KB I2C SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24C08LGI | 制造商:Catalyst Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。