- 您現在的位置：買賣IC網 > PDF目錄369653 > CAT22C10PA-30-TE13 256-Bit Nonvolatile CMOS Static RAM PDF資料下載
參數資料
| 型號： | CAT22C10PA-30-TE13 |
| 英文描述： | 256-Bit Nonvolatile CMOS Static RAM |
| 中文描述： | 256位非易失性的CMOS靜態RAM |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 514K |
| 代理商： | CAT22C10PA-30-TE13 |
CAT22C10
6
Doc. No. 1082, Rev. O
DEVICE OPERATION
The configuration of the CAT22C10 allows a common
address bus to be directly connected to the address
inputs. Additionally, the Input/Output (I/O) pins can be
directly connected to a common I/O bus if the bus has
less than 1 TTL load and 100pF capacitance. If not, the
I/O path should be buffered.
When the chip select (
CS
) pin goes low, the device is
activated. When CS is forced high, the device goes into
the standby mode and consumes very little current. With
the nonvolatile functions inhibited, the device operates
like a Static RAM. The Write Enable (
WE
) pin selects a
write operation when
WE
is low and a read operation
when
WE
is high. In either of these modes, an array byte
(4 bits) can be addressed uniquely by using the address
lines (A
0
–A
5
), and that byte will be read or written to
through the Input/Output pins (I/O
0
–I/O
3
).
The nonvolatile functions are inhibited by holding the
STORE
input and the
RECALL
input high. When the
RECALL
input is taken low, it initiates a recall operation
which transfers the contents of the entire EEPROM
array into the Static RAM. When the
STORE
input is
taken low, it initiates a store operation which transfers
the entire Static RAM array contents into the EEPROM
array.
Standby Mode
The chip select (
CS
) input controls all of the functions of
the CAT22C10. When a high level is supplied to the
CS
pin, the device goes into the standby mode where the
outputs are put into a high impendance state and the
power consumption is drastically reduced. With I
SB
less
than 100
μ
A in standby mode, the designer has the
flexibility to use this part in battery operated systems.
Read
When the chip is enabled (
CS
= low), the nonvolatile
functions are inhibited (
STORE
= high and
RECALL
=
high). With the Write Enable (
WE
) pin held high, the data
in the Static RAM array may be accessed by selecting an
address with input pins A
0
–A
5
. This will occur when the
outputs are connected to a bus which is loaded by no
more than 100pF and 1 TTL gate. If the loading is greater
than this, some additional buffering circuitry is recom-
Figure 1. Read Cycle Timing
ADDRESS
CS
DATA I/O
tRC
tCO
tAA
tLZ
tOH
tHZ
HIGH-Z
DATA VALID
相關PDF資料 |
PDF描述 |
|---|---|
| CAT22C10PI-20-TE13 | 256-Bit Nonvolatile CMOS Static RAM |
| CAT22C10PI-30-TE13 | 256-Bit Nonvolatile CMOS Static RAM |
| CAT22C10W-20-TE13 | 256-Bit Nonvolatile CMOS Static RAM |
| CAT22C10W-30-TE13 | 256-Bit Nonvolatile CMOS Static RAM |
| CAT22C10WA-20-TE13 | 256-Bit Nonvolatile CMOS Static RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT22C10PI-20 | 功能描述:NVRAM 256bit (64x4) 5V RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube |
| CAT22C10PI-20TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:256-Bit Nonvolatile CMOS Static RAM |
| CAT22C10PI-20-TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:256-Bit Nonvolatile CMOS Static RAM |
| CAT22C10PI-30 | 功能描述:NVRAM 256bit (64x4) 5V RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube |
| CAT22C10PI-30TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:256-Bit Nonvolatile CMOS Static RAM |
發布緊急采購，3分鐘左右您將得到回復。