- 您現在的位置：買賣IC網 > PDF目錄366669 > CAT1026LE-25TE13 Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM PDF資料下載
參數資料
| 型號： | CAT1026LE-25TE13 |
| 英文描述： | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| 中文描述： | 雙電壓監控電路，帶有I2C串行的2K位CMOS EEPROM的 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 153K |
| 代理商： | CAT1026LE-25TE13 |
7
CAT1026, CAT1027
Doc No. 3010, Rev. K
Data Protection
The CAT1026 and CAT1027 devices have been designed
to solve many of the data corruption issues that have long
been associated with serial EEPROMs. Data corruption
occurs when incorrect data is stored in a memory location
which is assumed to hold correct data.
Whenever the device is in a Reset condition, the embedded
EEPROM is disabled for all operations, including write
operations. If the Reset output(s) are active, in progress
communications to the EEPROM are aborted and no new
communications are allowed. In this condition an internal
write cycle to the memory can not be started, but an in
progress internal non-volatile memory write cycle can not
be aborted. An internal write cycle initiated before the
Reset condition can be successfully finished if there is
enough time (5ms) before VCC reaches the minimum
value of 2 V.
In addition, to avoid data corruption due to the loss of
power supply voltage during the memory internal write
operation, the system controller should monitor the
unregulated DC power. Using the second voltage sensor,
V
SENSE
, to monitor an unregulated power supply, the
CAT1026 and CAT1027 signals an impending power
failure by setting V
LOW
low.
Watchdog Timer
The Watchdog Timer provides an independent protection
for microcontrollers. During a system failure, the CAT1027
device will provide a reset signal after a time-out interval
of 1.6 seconds for a lack of activity. CAT1027 is designed
with the Watchdog timer feature on the WDI pin. If WDI
does not toggle within 1.6 second intervals, the reset
condition will be generated on reset output. The watchdog
timer is cleared by any transition on monitored line.
As long as reset signal is asserted, the watchdog timer
will not count and will stay cleared.
DEVICE OPERATION
Reset Controller Description
The CAT1026 and CAT1027 precision RESET
controllers ensure correct system operation during
brownout and power up/down conditions. They are
configured with open drain RESET outputs.
During power-up, the RESET outputs remain active
until V
CC
reaches the V
TH
threshold and will continue
driving the outputs for approximately 200 ms (t
PURST
)
after reaching V
TH
. After the t
PURST
timeout interval, the
device will cease to drive the reset outputs. At this point
the reset outputs will be pulled up or down by their
respective pull up/down resistors.
During power-down, the RESET outputs will be active
when V
CC
falls below V
TH
. The
RESET
output will be
valid so long as V
CC
is >1.0 V (V
RVALID
). The device is
designed to ignore the fast negative going V
CC
transient
pulses (glitches).
Reset output timing is shown in Figure 1.
Manual Reset Capability
The
RESET
pin can operate as reset output and manual
reset input. The input is edge triggered; that is, the
RESET
input will initiate a reset timeout after detecting
a high to low transition.
When
RESET
I/O is driven to the active state, the 200
msec timer will begin to time the reset interval. If external
reset is shorter than 200 ms, Reset outputs will remain
active at least 200 ms.
Monitoring Two Voltages
The CAT1026 and CAT1027 feature a second voltage
sensor, V
SENSE
, which drives the open drain V
LOW
output low whenever the input voltage is below 1.25 V.
The auxiliary voltage monitor timing is shown in Figure
2.
By using an external resistor divider the sense circuitry
can be set to monitor a second supply in the system.
The circuit shown in Figure 3 provides an externally
adjustable threshold voltage, V
TH_ADJ
to monitor the
auxiliary voltage. The low leakage current at V
SENSE
allows the use of large value resistors, to reduce the
system power consumption. The V
LOW
output can be
externally connected to the RESET output to generate
a reset condition when either of the supplies is invalid.
In other applications, V
LOW
signal can be used to
interrupt the system controller for an impending power
failure notification.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1026LE-28TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026LE-30TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026PI-25TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026PI-28TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
| CAT1026RE-25TE13 | Dual Voltage Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT1026LI25 | 功能描述:監控電路 2K bit 2.5V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026LI-25-G | 功能描述:監控電路 CPU w/2K RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026LI28 | 功能描述:監控電路 2K bit 2.8V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026LI-28-G | 功能描述:監控電路 CPU w/2K RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026LI30 | 功能描述:監控電路 2K bit 3V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。