- 您現在的位置：買賣IC網 > PDF目錄366663 > CAT1024LI-45T2 Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset PDF資料下載
參數資料
| 型號： | CAT1024LI-45T2 |
| 英文描述： | Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| 中文描述： | 監控電路，帶有I2C串行的2K位CMOS EEPROM和手動復位 |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 267K |
| 代理商： | CAT1024LI-45T2 |
CAT1024, CAT1025
Doc. No. 3008 Rev. N
10
2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
ACKNOWLEDGE
After a successful data transfer, each receiving
device is required to generate an acknowledge. The
acknowledging device pulls down the SDA line
during the ninth clock cycle, signaling that it received
the 8 bits of data.
The CAT1024/25 responds with an acknowledge
after receiving a START condition and its slave
address. If the device has been selected along with
a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT1024/25 begins a READ mode it
transmits 8 bits of data, releases the SDA line and
monitors the line for an acknowledge. Once it
receives this acknowledge, the CAT1024/25 will
continue to transmit data. If no acknowledge is sent
by the Master, the device terminates data transmis–
sion and waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/ˉˉ bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
a 8-bit address that is to be written into the address
pointers of the device. After receiving another acknow-
ledge from the Slave, the Master device transmits the
data to be written into the addressed memory location.
The CAT1024/25 acknowledges once more and the
Master generates the STOP condition. At this time, the
device begins an internal programming cycle to non-
volatile memory. While the cycle is in progress,
the device will not respond to any request from the
Master device.
Figure 5. Start/Stop Timing
Figure 6. Acknowledge Timing
Figure 7: Slave Address Bits
START BIT
SDA
STOP BIT
SCL
ACKNOWLEDGE
1
START
SCL FROM
MASTER
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
1
0
1
0
0
0
0
R/W
Default Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1024YI-42T2 | Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024YI-42T3 | Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024YI-45 | Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024YI-45-GT2 | Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024YI-45-GT3 | Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT1024LI-45T3 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024LI-45TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024PE-25 | 功能描述:監控電路 2K bit 2.5V Ext Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1024PE-25TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset |
| CAT1024PE-25-TE13 | 功能描述:監控電路 2K bit 2.5V Ext Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。